Pass Your Cisco 640-916 Exam Easy!

congras Moh,
question, where can we find the 187Q vce?

Passed today.
I used 187 Q.

The premium file is valid passed today

Passed today with 9XX. Premium file super valid!

Hello Everyone.

These dumps are valid. Dumps are not 100% valid you can pass the exam with help of these dumps. there are few question which are not in dump link 1 drag and drop question.

Also the 2 sims which are given in dumps are not in exam. There are other 2 labs, one for port channel and other is for vc.

Today i gave the exam and pass with 9XX.

189q Valid. Passed today.

18xq still valid

191q VCE is valid only

Hi, is this dump still valid?

could any one upload 181q, 187q, 189q dumps please

Hi who has the valid dumps? can you share it with us please. badly need it guys

Please, don't said that vce 182q, 187q, or 189q are valid, and share it.

182q is 99% accurate. Pass this morning with 986.

@abdulkadir: can you please provide these latest questions 181.please confirm.

@abdulkadir: Where you find these VCE ? (187q, 189q etc ...)

Hello,

181q, 187q, 189q all the same are vaild.

Passed today with 986.

Can anyone else confirm that the premium file is the valid dump to pass this exam?

Passed the exam today. The 187q dump is still valid. Scenarios are from VPC configuration and FCOE NPV. Drag & Drop is still from 147 dump.pass rate was 797 with 65 questions within 120 minutes.

Hi Esra's,

You have been looking for this exam long long time.

Which dumps did you use?
81q, 189q, 147q or 67q with screenshot images?

Thanks

Hello,

i passed today, there is valid dumps

Folks, just to clarify: the Premium dump has 187 questions, it's wrong in the file description (not 146q).
Please, when you share your exam experience, tell everybody which exam did you use to study in order to know if they are good or not.
Thanks

Alecsandre what file did you use, was is it the premium file?

Hello friends, what did you studied that is not enough? share the experience please

I failed the exam 06/06. New questions and new laboratories.

Hello Everyone,

please share your experience if you sat for this exam recently!

Thanks.

Mao might have used the free vce file.

Just failed 916 as Mao said about 30 new questions. Does anyone know a valid dumup
I did not tried premium.
Thank you.

Premium file is not enough to pass...
you need to read the cisco official guide and have some related experience.

@Mao,
Did you study with the Premium File?? Or which one did you use for?

30 new questions and 2 new labs over 65... you need 797 to pass...there's no valid dump guys!!

Labs were mixed questions with no CLI (not OTV and vPC labs)

Anyone can share the 182 exam file ? Thanks .

@yasser,

can u upload the valid vce file to this forum? ur action will be greatly appreciated by us.

Folks, which dump is the 180q one please? It is nowhere to be found..

182 is valid till now

please any one confirm if the 147q is valid or not and is there any lab question in the exam or not

Where is this 187q on the site, is to share so you can take the exam?

Passed the exam today, dump 187q VALID.
Good Luck.

I don't know what this The 182q dump is and where to get it from but any (free) dump on this website is EXTREMELY outdated and NOT valid....

Failed today with 767 score and needed 797.
I only got 10 out of 65 questions from all the dumps on this site.

Passed the exam today. The 182q dump is still valid. Only had 2 questions on the exam that weren't in the dump.

is 147 dump is valid or not and is there any lab in the exam or not ????

182q is 99% valid. Taken the exam on Monday 961 points. Only one new lab on VPC not difficult at all.

182q is valid

Guys the 182 is valid. Only one lab is not from the dumps. It is on VPC and it isn't hard. Otherwise all the questions are from the dump. You'll have to Google where to get it from.

Hello,

please tell me which one is valid!!

Thanks,

can someone please confirm if 182q is still valid?

Can someone please confirm if 182q is valid ? i am planning to take exam soon. Thanks!

Someone said 147 is valid, but others say not valid. Someone said 182 is valid, but others say not valid. Not sure at this point...

Which dump is valid

Can anyone share the valid file?

is the dump 182 q valid or not

@Mashti

Where can i find GoAndPass_Mashti_640-916_181Q.vce

No body is telling about 182 even the Admin says 147 is updated please guys helpout

is 147 dump valid

I did the exam last week

I uploaded my new VCE File (GoAndPass_Mashti_640-916_181Q.vce).

is 147 on actual test or 182 dump is valid

182q not valid, failed today!

Where can we find the 182q file

Anybody can tell me where i can find this 182 Premium file,i can only see 147 Premium file.

Esra'a; the 182q is valid

Hi all,

did anyone pass the exam this mounth?
Is it stil valid? i have the 147q dump.

@djd please tell me when did you take the exam?

182q is still valid; only one lab is new and that is very easy and not hard; it's about vpc "the first question about which the exhibit enable the vpc feature, the answer exhibit 1; the second question about which exhibit configure port-channel and the answer exhibit 2 or 5 i'm not remember but when you open the exhibit u can check port-channel configure; and the third and fourth i cannot remember the question but it's talk about vpc keepalive ;

all the questions came from 182q just one lab and u can pass if u don't answer the lab because u need 797 to pass the exam and 65

The old 147 question dump is still valid. Base from experience.

Guys,

there is new dumps did anyone try them?

Thanks,

Hi Alex,

Which dumps did you use?

Thanks,

Hi Alex,
Did you use the new 186q dump, or the old 147q one?
Thank you!

not valid. maybe 500pts with this dumb and no datacenter knowledge or training.

Hi all,
Has anyone tried the new 186q PDF?
I'm curious to see if it's up to date. At Actual Tests they only have the outdated 147q one.

Hello ,
please anyone attended the exam or willing to attend , PLEASE KEEP US UPDATED REGARDING THE dump news and exam details .

Guys, did any one buy the new dumps? they changed from 147 to 189!

Selam Ismail,

I dont remember the quesitons well but I scored 700p, lab questions are not easy.

As you see, Im looking for updates.

This dump is NOT valid. Cisco updated their CCNP DC exam pools back in November / December. I have taken this exam twice in the last 2 months and there were 4 or 5 questions from this pool.

Dear @abdulkadir kilic,

Can you please mention the labs which appeared in exam? Is there any configuration to be done or just the hotspot questions? Please mention the exact lab topics

This dump is not valid.

Any update guys!
For those who passed the exam, could you share your experience?

if you see our comments, share your exp !
i have failed a month ago, different labs, different but not difficult questions.

any updates!

Any updates?????

Have contacted support - useless. I have told that 147 Q&A is out of date but they keep saying it is current ???

Any update with the vce file?

any updates!!!!!

any updates guys, i need to take the exam soon

These are well out of date now. Even the latest with 147 Q&As is out of date. I failed the other day having 750 (pass rate was 787 I think).
There were 65 questions on the exam and only around 20 were from the dump. We need the updated version please!

Hello,

is there any update about it?

helloooo,

Anyone entered the exam? please help

Guys, is there any news about any new dumps?

invalid, failed today and there is a lot of new questions, N1K .... core layer ... labs ... VPC ......

Only 20-30% came from 147 dumps. Scenarios are from VPC configuration and FCOE NPV. Drag & Drop is still from 147 dump. New questions are mostly in UCS and N1000v.

Plz Can any one send me the latest Dump PDF Mail : shadymagdy@msn.com

Guys,

do you know if 147Q is failed or not?

please help me

Whatever 147 is not valid anymore even sims.

PLEASE COULD YOU SEND IT BY PDF

MY EMAIL : elsayed.wafi83@gmail.com

is the 147Q still valid?

Hello NED10,
could you send us the 147q please??

My email is qtjune98@live.com

Thank you.

Hi NED10, could you send us the 147q please??


My email is leogp23@msn.com

Dear NED please can you send me the dump.
karimgamil83@gmail.com

Dumps 147q is valid. Passed day before with 9xx. Passing score is 797

Failed today ....dump is not valid
All the questions are valid but answers are not

please send valid dump to pureattention@gmail.com have the exam on 12th nov

Hey Dude, could u please tell us about the drag and drop questions? thank u so much

Hello , kindly guy please sent the valid dump 640-916 to torworldcupaec@gmail.com thank so much.

This dump is NOT VALID, failed today. Few questions from this dump - mostly from lab. but most of questions completely new.

Passed the exam, some questions here are valid but most of them are not. If you have studied well take a look at this dump, if you plan to just dump yourself through you will not pass with this.

Hello shey , pls send me the file .

Thank you

otule.james@gmail.com

Has anyone passed the exam with this dump, this month? thank you

I have passed the exams through premium 147 is valid some new question but proper preparation will get you there

please send me the file.

Plz share the latest dumps for 640-916. Urgent request
harish.kansal@gmail.com

I do not understand why you do not study instead do only do tests...I' ve met people that passed the exam using only test and their preparation is 30% compared to a person who has studied.

can anyone update this dump, with valid questions? thank you

Please I need to retake the test. there is a new dump Cisco.ActualTests.640-916.v2015-08-18.by.itexamfoxVICTIM.127q.vce

I gave the test a month ago and fails, examining VICTIM.vce have some questions that I saw in the examination. The DRAG AND DROPS missing.

If anyone can upload a new exam is be grateful.

Hi Guys,
Can anyone pls post updated question set here. thanks.

This questions are valid but it represents only the 30% of the exam. A lot of new questions about UCS, UCS and vmware, and storage. Be ready to Cloud.

I was told my actualtests that they will have an update in 4 weeks. I am waiting till then to sit the exam.

Not Valid, failed a few days ago

Please share valid materials

Actual has the new one, it works. Tested recently

Failed as well with this version.

Since the dumps are now IVALID, does anyone know where to get the new dumps? One that is not outdated %80?

Kindly respond,
Thanks

Not valid anymore, there are a lot of new question. FAILED today..

A valid dump should also include a drag and drop question about FEX

Also check for NPIV , EIH, Waas D&D and Virtualization technology D&D, dumps without this topics and lots of design Q are not valid at all. Please share if you found a valid one !!!

The latest comment is somewhat confusing WAAS is one very short chapter 2 - 3 pages in the CCNA Data Center DCICT 640-916 Official Cert Guide and there is no mention of WAAS in Cisco's exam description????

lot of questions about WAAS. if the dumps you are looking at don't have questions about WAAS, don't consider it to be up to date.
mini-labs are the same.

Anyone know about this dump?
640-916 Cisco Dumps4free Jul-2015 By Shea

Not Valid. Just finished the exam

Dump NOT valid. I tested a few days ago and got 765/1000.

NOT VALID, took it today only a few questions from this dump in the current test.

Can someone please update the dump with new questions or list them here. Thanks for your help!

Just took the exam 5 minutes ago. The Actual Tests exam is NOT valid. There are very questions on this test.

NOT VALID.

Any one taking 916 exam this week ????, to double check if is still valid

Any one taking 916 exam this week ????, to double check if is still valid

Is not valid! Only few questions was found in the exam.

Invalid dumps

Dumps invalid, 80% new

Not valid! Failed today with 625 points.

Not valid! Failed today with 616 points. Only 10% from this dump was in the exam.

Not valid!! Failed today with 650 points. Only 10% from this dump.

valid, read 18 extra questions

Hi, based on the comments below, looks like most of the questions are coming from this dump. Can someone guide us on if there is any simulation or labs in the exam? and if so does this dump covers them as well. Thanks

This dump is still valid. I passes the exam on today (9 July 2015) with score 932/100. I found 1 new question and 1 rearrange existing question (it's similar Which of these Cards support virtual interfaces? (choose four)
options were different than what is in the dump
- VIC-1240
-VIC-1280
-NK61
-NK71
-VIC-1225
-VIC-1228 ) but the answer choices are different .

please anyone tell that my CCNA will be expired, and I pass 640-916. so my CCNA will keep valid?

please anyone tell that my CCNA will be expired, and I pass 640-916. so my CCNA will keep valid?

This dump still valid 100%, remember to study also the 18Q.

Passed the Cisco Introducing Cisco Data Center Technologies today.

I followed http://www.actualtests.com/exam-640-916.htm

The Actual Test are totally valid!

Best Luck to you all!

The dump is valid i passed with 977 on (29/6/2015)

100% valid , i passed with 1000 today.. don't forget the additional question below

Dear Harish,

Please leave a feedback afterwards.

Good luck :)

I am planning to write this exam this week, can you please let me know if this dump is still valid

I wanted to know how many simlets or hotspot questions are on the exam?

We're there any simlets on this test? If so, how many?

Passed the exam today, dumps are 100% valid. Read additional questions and answers posted by david and Amir.

100% valid , passed with 100% score

is still valid?

Exact question and options.
Q. Which of these Cards support virtual interfaces? (choose four)
A- VIC-1240
B- VIC-1280
C- NK61
D- NK71
E- VIC-1225
F- VIC-1227

Answers: A, B, E, F.
Explanation: http://www.cisco.com/c/en/us/products/interfaces-modules/unified-computing-system-adapters/models-listing.html

Still valid , passed today (1000/1000).
Good luck.

VALID, I passed today (29/04/2015) Make sure you study below questions too.

Q.No.1
In a large enterprise, which two SAN switches are ideal core switches for providing high
availability? (Choose two.)

A. Cisco Nexus 5548
B. Cisco MDS 9710
C. Cisco MDS 9509
D. Cisco Nexus 7028
E. Cisco MDS 9222i

Answer: B, C

Q.No.2
Which three options are characteristics of a data centre access layer switch? (Choose three.)

A. host connectivity
B. firewall connectivity
C. QoS marking
D. spanning-tree edge ports
E. high-speed packet switching

Answer: A, C, D

Q.No.3

In a three-tiered data center network design, where does the Layer 2 / Layer 3 boundary typically
reside?

A. core layer
B. aggregation layer
C. access layer
D. services layer

Answer: B

Q.No.4
Which two methods to configure LACP port channels are valid? (Choose two.)

A. channel-group 10 mode active
B. port-channel 10 mode active
C. channel-group 10 mode on
D. channel-group 10 mode passive
E. channel-group 10 mode lacp

Answer: A, D


Q.No.5
Which two switches does Cisco recommend for small and medium-sized organizations to provide
a cost-effective solution for the Fibre Channel SAN edge? (Choose two.)

A. Cisco MDS 9250i
B. Cisco MDS 9506
C. Cisco MDS 9148
D. Cisco MDS 9509

Answer: A, C

Q.No.6
Which two switches provide high-performance, multiprotocol, and multiple services for the Fibre
Channel SAN core in the data center? (Choose two.)

A. Cisco MDS 9124
B. Cisco MDS 9506
C. Cisco MDS 9222i
D. Cisco MDS 9710

Answer: B, D

Q.No.7
Which four components are parts of the Cisco Data Center Nexus switching offering? (Choose
four.)

A. Cisco 6000 Series Switch
B. Cisco ASR 9000
C. Cisco 1000v Switch
D. Cisco IOS Software
E. Cisco 4500E Switch
F. Cisco NX-OS Software
G. Cisco 6509-E Switch
H. Cisco Fabric Extender

Answer: A,C,F,H
Q.No.8
On the Cisco Nexus 5000, which three commands help verify network connectivity? (Choose
three.)

A. ping
B. show interface brief
C. show OTV
D. show VDC membership
E. TRACEROUTE

Answer: A, B, E

Q.No.9
Which three items are needed to perform the initial setup for a Cisco Data Center device?
(Choose three.)

A. IP address and network mask
B. FTP password
C. Active Directory password
D. console cable
E. device software licenses
F. admin password to assign to the device
G. SFP+ cables

Answer: A, D, F

Q.No.10
Which settings are used to access the console port on the Cisco Nexus?

A. 9600, 8 data bits, 1 stop bit, No parity
B. 19200, 8 data bits, 1 stop bit, No parity
C. 9600, 8 data bits, 0 stop bit, No parity
D. 9600, 8 data bits, 1 stop bit, Parity

Answer: A

Q.No.11
Which three items are control plane protocols? (Choose three.)

A. OSPF
B. UDLD
C. CoPP
D. IS-IS
E. NAT

Answer: A, B, D

Q.No.12
Which SAN port type allows multihop FCoE between two SAN switches?

A. VN
B. VE
C. VF
D. E

Answer: B



Q.No.13
For which two reasons should customers deploy FCoE beyond the access layer? (Choose two.)

A. higher throughput compared to traditional Fibre Channel
B. better security than traditional Fibre Channel
C. device consolidation
D. FCoE cannot be deployed beyond the access layer.

Answer: A, C

Q.No.14
Which option describes what VNTags are used for?

A. to separate broadcast domains
B. to identify and separate virtual interfaces
C. to prioritize FCoE traffic
D. to extend a Layer 2 domain across a Layer 3 boundary

Answer: B

Q.No.15
Which option describes the function of a Cisco Nexus 2000?

A. positioned for access layer switching
B. to expand the port density of a parent switch
C. to provide edge routing
D. to host virtual appliances

Answer: B

Q.No.16
Which three components are needed to implement FCoE? (Choose three.)

A. FCoE Initialization Protocol
B. N_Port virtualization
C. N_Port ID virtualization
D. converged network adapter
E. priority flow control

Answer: A, D, E






Q.No.17
Which three devices support FCoE? (Choose three.)

A. Cisco Nexus 5500
B. Cisco Nexus 7000
C. Cisco Nexus 3000
D. Cisco Nexus 1000V
E. Cisco UCS Fabric Interconnect

Answer: A, B, E

Q.No.18

After you install and configure a Cisco Nexus 5548, you notice that you cannot ping its default
gateway. Assume that your management interface is up and running, and other devices in the
same subnet or VLAN can communicate with the default gateway.

Which statement describes the problem?

A. The subnet of the management port is incorrect.
B. The default route is configured incorrectly.
C. You are using the incorrect cable.
D. You must ping from the management VRF.

Q.19 Which of these Cards support virtual interfaces? (choose four)
options were different than what is in the dump
- VIC-1240
-VIC-1280
-NK61
-NK71
-VIC-1225
-VIC-1228

Cleared today. Dumps valid. Pl make sure you read the below additional 19 questions also.

Is this valid dump?

i am sitting for this exam this week. Please advise if this is valid or are they any new questions apart from the dumps and 19 additional questions.

is this a valid dump?

Does this dump hold valid still?

Rgds-Netrace

TerrorWolf , THANK YOU!!!!

Exam still valid, noting new !!!!

@ Leo: there is noting to configure like Cisco R&S exam but there is an OTV lab.
In that lab you just have to give show commands and answer the questions, that is all.

Cheers

Is this exam have any lab question like CCNA R&S??

Got 954 on 4/2/2015. Used the 81Q dump with Faisal/Amjad's 18Q. I can't open this dump but I think it is same as my dump with the 18Q. Maybe 2 answers are incorrect. The dump is still valid.

Passed today with 977.. questions are still valid... and don't forget the extra questions below

Did Exam today . got 954 marks.
Dump is valid but you have to prepare for these questions as well.

Q.No.1
In a large enterprise, which two SAN switches are ideal core switches for providing high
availability? (Choose two.)

A. Cisco Nexus 5548
B. Cisco MDS 9710
C. Cisco MDS 9509
D. Cisco Nexus 7028
E. Cisco MDS 9222i

Answer: B, C

Q.No.2
Which three options are characteristics of a data centre access layer switch? (Choose three.)

A. host connectivity
B. firewall connectivity
C. QoS marking
D. spanning-tree edge ports
E. high-speed packet switching

Answer: A, C, D

Q.No.3

In a three-tiered data center network design, where does the Layer 2 / Layer 3 boundary typically
reside?

A. core layer
B. aggregation layer
C. access layer
D. services layer

Answer: B

Q.No.4
Which two methods to configure LACP port channels are valid? (Choose two.)

A. channel-group 10 mode active
B. port-channel 10 mode active
C. channel-group 10 mode on
D. channel-group 10 mode passive
E. channel-group 10 mode lacp

Answer: A, D


Q.No.5
Which two switches does Cisco recommend for small and medium-sized organizations to provide
a cost-effective solution for the Fibre Channel SAN edge? (Choose two.)

A. Cisco MDS 9250i
B. Cisco MDS 9506
C. Cisco MDS 9148
D. Cisco MDS 9509

Answer: A, C

Q.No.6
Which two switches provide high-performance, multiprotocol, and multiple services for the Fibre
Channel SAN core in the data center? (Choose two.)

A. Cisco MDS 9124
B. Cisco MDS 9506
C. Cisco MDS 9222i
D. Cisco MDS 9710

Answer: B, D

Q.No.7
Which four components are parts of the Cisco Data Center Nexus switching offering? (Choose
four.)

A. Cisco 6000 Series Switch
B. Cisco ASR 9000
C. Cisco 1000v Switch
D. Cisco IOS Software
E. Cisco 4500E Switch
F. Cisco NX-OS Software
G. Cisco 6509-E Switch
H. Cisco Fabric Extender

Answer: A,C,F,H
Q.No.8
On the Cisco Nexus 5000, which three commands help verify network connectivity? (Choose
three.)

A. ping
B. show interface brief
C. show OTV
D. show VDC membership
E. TRACEROUTE

Answer: A, B, E

Q.No.9
Which three items are needed to perform the initial setup for a Cisco Data Center device?
(Choose three.)

A. IP address and network mask
B. FTP password
C. Active Directory password
D. console cable
E. device software licenses
F. admin password to assign to the device
G. SFP+ cables

Answer: A, D, F

Q.No.10
Which settings are used to access the console port on the Cisco Nexus?

A. 9600, 8 data bits, 1 stop bit, No parity
B. 19200, 8 data bits, 1 stop bit, No parity
C. 9600, 8 data bits, 0 stop bit, No parity
D. 9600, 8 data bits, 1 stop bit, Parity

Answer: A

Q.No.11
Which three items are control plane protocols? (Choose three.)

A. OSPF
B. UDLD
C. CoPP
D. IS-IS
E. NAT

Answer: A, B, D

Q.No.12
Which SAN port type allows multihop FCoE between two SAN switches?

A. VN
B. VE
C. VF
D. E

Answer: B



Q.No.13
For which two reasons should customers deploy FCoE beyond the access layer? (Choose two.)

A. higher throughput compared to traditional Fibre Channel
B. better security than traditional Fibre Channel
C. device consolidation
D. FCoE cannot be deployed beyond the access layer.

Answer: A, C

Q.No.14
Which option describes what VNTags are used for?

A. to separate broadcast domains
B. to identify and separate virtual interfaces
C. to prioritize FCoE traffic
D. to extend a Layer 2 domain across a Layer 3 boundary

Answer: B

Q.No.15
Which option describes the function of a Cisco Nexus 2000?

A. positioned for access layer switching
B. to expand the port density of a parent switch
C. to provide edge routing
D. to host virtual appliances

Answer: B

Q.No.16
Which three components are needed to implement FCoE? (Choose three.)

A. FCoE Initialization Protocol
B. N_Port virtualization
C. N_Port ID virtualization
D. converged network adapter
E. priority flow control

Answer: A, D, E






Q.No.17
Which three devices support FCoE? (Choose three.)

A. Cisco Nexus 5500
B. Cisco Nexus 7000
C. Cisco Nexus 3000
D. Cisco Nexus 1000V
E. Cisco UCS Fabric Interconnect

Answer: A, B, E

Q.No.18

After you install and configure a Cisco Nexus 5548, you notice that you cannot ping its default
gateway. Assume that your management interface is up and running, and other devices in the
same subnet or VLAN can communicate with the default gateway.

Which statement describes the problem?

A. The subnet of the management port is incorrect.
B. The default route is configured incorrectly.
C. You are using the incorrect cable.
D. You must ping from the management VRF.

Q.19 Which of these Cards support virtual interfaces? (choose four)
options were different than what is in the dump
- VIC-1240
-VIC-1280
-NK61
-NK71
-VIC-1225
-VIC-1228

Hello Every one..

Just wanted to confirm that is that any new HOT Spot question or any changes in old hot spot questions. please reply fast as I am going to give this paper next week.

thanks

new questions

QUESTION NO: 82

In a large enterprise, which two SAN switches are ideal core switches for providing high
availability? (Choose two.)


A. Cisco Nexus 5548
B. Cisco MDS 9710
C. Cisco MDS 9509
D. Cisco Nexus 7028
E. Cisco MDS 9222i

Answer: B,C
Explanation:



QUESTION NO: 83

Which three options are characteristics of a data center access layer switch? (Choose three.)


A. host connectivity
B. firewall connectivity
C. QoS marking
D. spanning-tree edge ports
E. high-speed packet switching

Answer: A,C,D
Explanation:



QUESTION NO: 84

In a three-tiered data center network design, where does the Layer 2 / Layer 3 boundary typically
reside?

Cisco 640-916 Exam
"Pass Any Exam. Any Time." - www.actualtests.com 47A. core layer
B. aggregation layer
C. access layer
D. services layer

Answer: B
Explanation:



QUESTION NO: 85

Which two methods to configure LACP port channels are valid? (Choose two.)


A. channel-group 10 mode active
B. port-channel 10 mode active
C. channel-group 10 mode on
D. channel-group 10 mode passive
E. channel-group 10 mode lacp

Answer: A,D
Explanation:



QUESTION NO: 86

Which two switches does Cisco recommend for small and medium-sized organizations to provide
a cost-effective solution for the Fibre Channel SAN edge? (Choose two.)


A. Cisco MDS 9250i
B. Cisco MDS 9506
C. Cisco MDS 9148
D. Cisco MDS 9509

Answer: A,C
Explanation:



QUESTION NO: 87

Which two switches provide high-performance, multiprotocol, and multiple services for the Fibre
Channel SAN core in the data center? (Choose two.)

Cisco 640-916 Exam
"Pass Any Exam. Any Time." - www.actualtests.com 48A. Cisco MDS 9124
B. Cisco MDS 9506
C. Cisco MDS 9222i
D. Cisco MDS 9710

Answer: B,D
Explanation:



QUESTION NO: 88

Which four components are parts of the Cisco Data Center Nexus switching offering? (Choose
four.)


A. Cisco 6000 Series Switch
B. Cisco ASR 9000
C. Cisco 1000v Switch
D. Cisco IOS Software
E. Cisco 4500E Switch
F. Cisco NX-OS Software
G. Cisco 6509-E Switch
H. Cisco Fabric Extender

Answer: A,C,F,H
Explanation:



QUESTION NO: 89

On the Cisco Nexus 5000, which three commands help verify network connectivity? (Choose
three.)


A. ping
B. show interface brief
C. show otv
D. show vdc membership
E. traceroute

Answer: A,B,E
Explanation:


Cisco 640-916 Exam
"Pass Any Exam. Any Time." - www.actualtests.com 49QUESTION NO: 90

Which three items are needed to perform the initial setup for a Cisco Data Center device?
(Choose three.)


A. IP address and network mask
B. FTP password
C. Active Directory password
D. console cable
E. device software licenses
F. admin password to assign to the device
G. SFP+ cables

Answer: A,D,F
Explanation:



QUESTION NO: 91

Which settings are used to access the console port on the Cisco Nexus?


A. 9600, 8 data bits, 1 stop bit, No parity
B. 19200, 8 data bits, 1 stop bit, No parity
C. 9600, 8 data bits, 0 stop bit, No parity
D. 9600, 8 data bits, 1 stop bit, Parity

Answer: A
Explanation:



QUESTION NO: 92

Which three items are control plane protocols? (Choose three.)


A. OSPF
B. UDLD
C. CoPP
D. IS-IS
E. NAT

Answer: A,B,D
Explanation:
Cisco 640-916 Exam
"Pass Any Exam. Any Time." - www.actualtests.com 50


QUESTION NO: 93

Which SAN port type allows multihop FCoE between two SAN switches?


A. VN
B. VE
C. VF
D. E

Answer: B
Explanation:



QUESTION NO: 94

For which two reasons should customers deploy FCoE beyond the access layer? (Choose two.)


A. higher throughput compared to traditional Fibre Channel
B. better security than traditional Fibre Channel
C. device consolidation
D. FCoE cannot be deployed beyond the access layer.

Answer: A,C
Explanation:



QUESTION NO: 95

Which option describes what VNTags are used for?


A. to separate broadcast domains
B. to identify and separate virtual interfaces
C. to prioritize FCoE traffic
D. to extend a Layer 2 domain across a Layer 3 boundary

Answer: B
Explanation:


Cisco 640-916 Exam
"Pass Any Exam. Any Time." - www.actualtests.com 51QUESTION NO: 96

Which option describes the function of a Cisco Nexus 2000?


A. positioned for access layer switching
B. to expand the port density of a parent switch
C. to provide edge routing
D. to host virtual appliances

Answer: B
Explanation:



QUESTION NO: 97

Refer to the exhibit.





After you install and configure a Cisco Nexus 5548, you notice that you cannot ping its default
gateway. Assume that your management interface is up and running, and other devices in the
same subnet or VLAN can communicate with the default gateway.


Cisco 640-916 Exam
"Pass Any Exam. Any Time." - www.actualtests.com 52Which statement describes the problem?


A. The subnet of the management port is incorrect.
B. The default route is configured incorrectly.
C. You are using the incorrect cable.
D. You must ping from the management VRF.

Answer: D
Explanation:



QUESTION NO: 98

Which three components are needed to implement FCoE? (Choose three.)


A. FCoE Initialization Protocol
B. N_Port virtualization
C. N_Port ID virtualization
D. converged network adapter
E. priority flow control

Answer: A,D,E
Explanation:



QUESTION NO: 99

Which three devices support FCoE? (Choose three.)


A. Cisco Nexus 5500
B. Cisco Nexus 7000
C. Cisco Nexus 3000
D. Cisco Nexus 1000V
E. Cisco UCS Fabric Interconnect

Answer: A,B,E
Explanation:




Cisco 640-916 Exam

Passed the exam today with 977 score. Had around 13-15 new questions.

1) What's the benefit of implementing fcoe beyond the access layer?
- Consolidated devices
-Better throughput than traditional FC
-Better Security than traditional FC
-Can't extend FCoE beyond access layer

2) What is required to complete initial setup of any data centre device? (choose 3)
-admin password
-console
-Software licenses
-ip addressing and password to assign
-Active Directory password
-FTP password

3) Which of these Cards support virtual interfaces? (choose four)
options were different than what is in the dump
- VIC-1240
-VIC-1280
-NK61
-NK71
-VIC-1225
-VIC-1228

4) What components are required to implement fcoe? (Choose 3)
-Priority flow control
-Converged Network Adapter
-Fcoe initialisation protocol
-Nport virtualization
-Nport id virtualization

5) Terminal Console setting for Nexus Device
-9600 , 1 stop bit , 8bits data , no partiy.

6) Large enterprises SAN core switch with multi protocol and multi services capability (Choose two)
-MDS9710
-MDS9513

7) Medium and Small enterprise SAN edge siwtches (Choose two)
-MDS 9148
-MDS 9250i

8) Correct LACP mode config (Choose two)
- Channel-group 10 mode active
-Channel-group 10 mode passive

9) Components of Cisco Nexus Switching in Datacenter (Choose four)
-N1000v
-NX-OS Software
-Fabric Extenders (FEX)
-Unified Computing System
-Cisco 6000 series switch
-6509-E switch
-ASR 9000
-4500-X switch

10) why i can't ping default gateway of management interface?
- Need to ping in VRF Management.

11) What is VNTag use for?
-Haven't remembered the options.

Good Luck to all!!

Have passed the exam. The dump is valid however there are about 15 to 20 new questions. Some of them are mentioned here so read the comments.
More that I remember below, however I am not sure about the answers.

Benefit of implementing fcoe beyond the access layer (beyond it not in it)

What is required for initial setup of any data centre device? Options were console, licenses, ip addressing, password to assign and 2 others. Choose 3

Cards supporting virtual interfaces: options were different than what is in the dump; mostly VIC cards in the exam.

What components are required to implement fcoe? Can remember 3 of 5 options
Fcoe initialisation protocol
Nport virtualization
Nport id virtualization

Dump is valid maybe 50 - 60 %. Rest all new questions. Please do not attempt sitting the exam based only on this dump as you will fail it. You need to really learn. good luck all

The dump is valid not 100% but in enough to pass, passed today. cheerz.

Please share datacenter 640-916 ebook link.

Is that dump is valid. please send updated questions which is came in recent papers will be more appreciable

Is there any lab in this exam?

Passed this exam. This is by far the best file todate. It has changed, so it is no longer 100% accurate. More like 75-80%. All of the HOTspots are the same, Look over the comments here to pick up some of the extra questions and topics to look at. It is doable. Good Luck!

benefit of use FCoE at access layer:
However,there are powerful benefits to implementing FCoE at the access layer and scaling horizontally
with the deployment of servers. These benefits include:
• Reduction in the number of adapters and network infrastructure devices
• Reduction in the number of cables
–– Allows economical blend of inexpensive copper and longer-link optical technologies
–– Reduces cable installation expenses
–– Significantly reduces the number of long cables
–– Can increase server density if server deployment is impeded by cable bulk or
airflow concerns
–– Reduces the possibility of air dams in the data center
–– Reduces cable maintenance and provisioning concerns in the data center
• Reduction in the amount of power used
• Reduction in space used due to switch equipment rack occupancy
• Reduction is server height due to fewer add-in card slot requirements if servers are
I/O bound
• Redeployment of power and space savings to provisioning of additional servers,
extending the life of the data center

It seems there is a new version of TK (updated the 24th nov) with 99 questions!!And there are around 20 questions more than this VCE. Bye

i passed the exam today .
the Dump still valied but theere are around 13 new questions :
that what i have remember
1- Termainl Console setting : 9600 , 1 stop bit , 8bitdat , no partiy.

2- Large enterprise SAN core switch mode : MDS9513 , MDS9710.

3- Medium and Small enterprise SAN core siwtch : MDS9128.

4- SAN multiservice switch : MDS9222i

5- LACP mode : Active & passive.

6- item to running Cisco Nexus Switch DC : ASR , N1000v , NX-OS , N7K

7- why i can't ping : the ping was failed cause didc't decide VRF Mgmgt.

8- Virtual network interfaces.

9- benefit of use FCoE at access layer.



don't worries the other question its very easy if you have basic network concept.

NOT VALID !!!!
I have about 40% new questions in the exam.
I Falied :(

hi
is this still valid..

There are quite a few questions added recently.

received at least 20 new questions past friday, not valid

still valid?

Is there any Lab in the exam? What are they?

People saying there are more new questions? - Can anyone confirm if there are now more questions than what is in this VCE? Still valid?

Failed today, more than half came outside of this dumps.

PAssed this exam on the 3 Nov 2014 with a pass of 958. exam valid. I received an exam that was heavy on the MDS stuff.

Brasil.

Still valid?

valid, more new questions, passed 867:
*parámetros para conectarse por consola al cisco nexus?
*2 Cisco MDS para grandes SANs?
*2 Cisco MDS para pequeñas y medianas SANs
*Realizan un ping desde un nexus 5548 y no alcanzan la Ip, preguntan porque? R=Deben hacerlo desde la vrf de Mgmt
*Mencionar 4 dispositivos que pertenecen a Data Center, vienen revueltos con dispositivos de R&S. R= nexus 1000v, NX-OS, ASRxx, nexus FEX.
*mencionar 2 formas de configurar LACP

I have about 30% new questions in the exam. If you learn hard, you can get it.

There are about 30% new questions in the exam. If you learn hard, you can get it.

100% Valid, Got 1000/1000

100% valid dump , passed today.
Note : Answers are totally shuffled.

100% valid, got 1000/1000 today. Answered today on 20/10/14

100% Valid... Passed yesterday with 989/1000. Answers are totally shuffled.

100% Valid.. Just pass today with 989/1000. Answers are totally shuffled.