Pass Your CompTIA N10-005 Exam Easy!

Greetings to all,i am in need of a valid itexamfox n+(N10-005) dump im willing to pay for the exam i reside in Johannesburg if you have send me a mail on rebone.segopolo@gmail.com

This is a decent dump. I read two different N+ books along with Messer's videos also. Passed this week with over 800 score. I'd say about 40% of my questions came from CLARA or INEZ. These dumps will help on the different questions as well. The sims are spot on, but a little harder to figure out in person. Only had to know /24 and up CIDR. Lots of wireless questions, study that well. Know your tools, cable speeds, and distances. Know OSI vs. TCP/IP models. Know troubleshooting steps. Don't forget port numbers either. Good luck.

Appeared for exam Nov 28 2014 and passed. Here are sims which are genrally asked I got 6 sims in my exam.
Simulation 1: Joining 2 Buildings with the most secure Wi-Fi and right antennas; choose left facing parabolic antenna and right facing parabolic antenna, security choose WPA-CCMP for both APs. Inside the building choose right facing directional antenna, Omni-directional and left facing directional antenna, set the security for all 3APs to open.

Simulation 2: have to match wording with the correct cabling tools (i.e crimper, punch down tool, cable tester, toner probe)

Simulation 3, There are 3 APs and the 2nd one has just been replaced and you need to change the channel to 6 so it doesn't overlap with the other 2, also change Speed to 100 and Duplex to Full, finally change the Mode to G.

Simulation 4: 4PCs are joined to the gateways and servers but some of them are not connecting to the servers, PC1 and 2 were working because I could ping the servers so it was only PC3 and 4 that were not connecting. PC3 I just changed the subnet mask to 255.255.255.0 because it was a /24 IP address, PC4 only changed the gateway, that’s all.

Simulation 5: Connect 2 Buildings that are 3km apart, make sure you select a single mode fibre, then you have to connect a PC, server to the patch panel and switch and also auto mdix is disabled.
Here is the secret of mastering it, remember that when you connect devices on the same OSI layer you use a cross-over cable, devices on different OSI layers use a straight-through cable.
So PC and Servers are layer 3, router layer 3, switch layer 2, patch panel layer 1.

Simulation 6: Your given departments in a company with a number of users in each department, and your also given an ip address and each department must fall under each subnet

Simulation7: Rearrange T56A and T568B wires in correct order. See Google images to remember wiring order.

Simulation 8: The eight steps for Troubleshooting
The most important part of troubleshooting any problem is to divide the tasks of problem resolution into a systematic process of elimination.
Cisco has broken this process into eight steps:
1. Define the problem.
2. Gather detailed information.
3. Consider probable cause for the failure.
4. Devise a plan to solve the problem.
5. Implement the plan.
6. Observe the results of the implementation.
7. Repeat the process if the plan does not resolve the problem.
8. Document the changes made to solve the problem.

Simulation 9: Mix of WAPs, Routers, Sw's, Wireless Laptops, Workstations and Servers in 2 sites. Two part question. Which device is causing some users to not receive internet access & why.
All of them had to add both DNS servers. A few had to change IP or subnet or gateway. Use command line to ping gateway & DNS Servers.

Simulation 10:
Router, Switch, Hub and Access Point ware given and for each of them we have to specify Multiple/Single Collision Domain or Multiple/Single Broadcast Domain

Regarding Multiple choice questions (84Q) -
I used Andrew's 525 Question VCE. But I just got about 30-40% questions from it. Not sure which VCE is 100% valid as of today.
Only thing needed to pass practice is with sub netting and other conceptual knowledge.

i took the exam today,pliz guys study,passed with 800 plus.gd luck

i took the exam 5hours ago today,i met with eight sims from this dump,please guys just study hard,gd luck

All you need is the Simulation that will follow this comment & 'Clara Q
& A, VCE. For me only about 2 to 4 question weren't from her q & a.
Took the Test on November 19,2014 Pass, with 800 plus.

An the simulations , T56B Network Wires:
Simulation 1: Joining 2 Buildings with the most secure Wi-Fi and right antennas, choose left facing parabolic antenna and right facing parabolic antenna, security choose WPA-CCMP for both APs. Inside the building choose right facing directional antenna, Omni-directional and left facing directional antenna, set the security for all 3APs to open.

Simulation 2: have to match wording with the correct cabling tools(i.e crimper, punch down tool, cable tester, Toner Probe, Loopback Plug, Protocol Analyzer, Multimeter, OTDR, etc.

Simulation 3, There are 3 APs and the 2nd one has just been replaced and you need to change the channel to 6 or 11 so it doesn't overlap with the other 2, also change Speed to 100 and Duplex to Full, finally change the Mode to G.

Simulation 4: 4PCs are joined to the gateways and servers but some of them are not connecting to the servers, PC1 and 2 were working because I could ping the servers so it was only PC3 and 4 that were not connecting. PC3 I just changed the subnet mask to 255.255.255.0 because it was a /24 IP address, PC4 only changed the gateway, that’s all.

Simulation 5, connect 2 Buildings that are 3km apart, make sure you select a single mode fiber, then you have to connect a PC, server to the patch panel and switch and also auto mdix is disabled: Here is the secret of mastering it, remember that when you connect devices on the same OSI model you use a cross-over cable, devices on different OSI models use a straight-through cable. So PC and Servers are layer 3, router layer 3, switch layer 2, patch panel layer 1.

Simulation 6: Your given departments in a company with a number of users in each department, and your also given an ip address and each department must fall under each subnet

Hope this will help and yes the dump is almost valid as it has some of the sims inside
Configure The Appropriate Devices
Answer: The switch are not connected properly. Connect switch 1 to switch 3 on the last port and then connect the last port of switch 3 to the first port of switch 2.
In this way the switches will be connected properly. Click ‘Enable All ‘ to enable the switch.
Answer : Cable Certifier – incorrectly crimped cable. Click – On ‘Submit’
128 64 32 16 8 4 2 1 T56B Network Wires: White/Orange, Orange, White/Green, Blue,
White/Blue, Green, White/Brown, Brown.

Hi Guys. I can't open these files it says the files have been created with the latest VCE than I have. Please assist.

Sorry to say that i only got maybe 10 questions from these dumps, but all labs are correct from WII K.
Even though i did not get questions from these dumps, knowing them helped me pass the exam with ease, 850/900, so if you know these questions you will most likely pass. Hope this helps. Learn what the different tools do, and what they look like, thats in the tools sim. Match the tool to the decsription of usage. Hope this helps

CLARA and INEZ are valid. I GOT LIKE 65 out of 80 QUESTIONS IN THE REAL TEST!!!
REVIEW WII K FROM AFRICA'S COMMENT. HE IS RIGHT ABOUT ALL THE SIMS. Took the test SEPTEMBER 25, 2014! 854-900!

please advise if this dump is valid, i will took this exam so soon.

is this dump valid? please i will be writing this coming thursday september 25th. :(

Any word on if this is valid or not?

Please guys and gals are these dumps valid.... I will be taking test tomorrow... Please let me know..

are this valid? im writing nextweek! please update! :( :(

Are these dumps valid? I am writing on 13th september. And if not, then can anyone please help me with what practice exams should I use

Are these dumps valid? I am writing on 13th september. And if not, then can anyone please help me with what practice exams should I use

Ola Gents, just wrote my exam today(03/09/14) in
south africa, the sims that were there are(NB:sims are not in order, copied and pasted answers from other exam collection peeps):

1: Joining 2 Buildings with the most secure Wi-Fi and right antennas, choose left facing parabolic antenna and right facing parabolic antenna, security choose WPA-CCMP for both APs. Inside the building choose right facing directional antenna, Omni-directional and left facing directional antenna, set the security for all 3APs to open.

Simulation 2: have to match wording with the correct cabling tools(i.e crimper, punch down tool, cable tester etc)

Simulation 3, There are 3 APs and the 2nd one has just been replaced and you need to change the channel to 6 so it doesn't overlap with the other 2, also change Speed to 100 and Duplex to Full, finally change the Mode to G.

Simulation 4: 4PCs are joined to the gateways and servers but some of them are not connecting to the servers, PC1 and 2 were working because I could ping the servers so it was only PC3 and 4 that were not connecting. PC3 I just changed the subnet mask to 255.255.255.0 because it was a /24 IP address, PC4 only changed the gateway, that’s all.

Simulation 5, connect 2 Buildings that are 3km apart, make sure you select a single mode fibre, then you have to connect a PC, server to the patch panel and switch and also auto mdix is disabled: Here is the secret of mastering it, remember that when you connect devices on the same OSI model you use a cross-over cable, devices on different OSI models use a straight-through cable. So PC and Servers are layer 3, router layer 3, switch layer 2, patch panel layer 1.

Simulation 6: Your given departments in a company with a number of users in each department, and your also given an ip address and each department must fall under each subnet

Hope this will help and yes the dump is almost valid as it has some of the sims inside

Took my Network+ exam on Friday August 29th one day before my birthday and passed with a score of 763. Learn CIDR.There are a few questions that deal with it(including some sims). There were about 6 or 7 sims in my exam. You have to reconfigure and reconnect 4 PC's that lost their network connectivity. Set up WAP's and security in 2 blgds by dragging and dropping the muliple antenna choices to the right location. Create a TIA/EIA-568-B cable by pairing the correct wire colors together. There's a sim that deals with configuring multiple switches and servers. I hope that helps!!!

Guyz z this valid and we need help with sims

guys do the sims change every months

Cooper M, did you not download this exam?

Good Luck with your exam, & please let me know if this exam helped.

Kindly awaiting your response.

Please help! I want to book soon, is this exam valid in South Africa?

is this valid?

Guys im writing on the 5th of Sep. Please assist with sims.