Search results

I
I need a printer that prints to CD/DVD

Actually, I just found out that Acoustica released an update around the middle of December in whihc the D5160 (amongst numerous others) are now supported. While I did like the color a bit better on the Epson R260 I used to have, it had a litany of problems, includinging giving errors every...
- imported_itsmezed
- Post #12
- Dec 30, 2006
- Forum: Computer Building
I
I need a printer that prints to CD/DVD

I'm pretty sure the D5160 isn't directly supported by the Accoustica software. I can't find any listing for it anywhere in the software. Speaking of the D5160 though... it only seems to want to print with full-face media. I have a stack of the regular printable DVDs as well, and it just...
- imported_itsmezed
- Post #10
- Dec 30, 2006
- Forum: Computer Building
I
Which Overclock Should I Use For E6600?

Which motherboard and bios version did you have?
- imported_itsmezed
- Post #3
- Sep 25, 2006
- Forum: CPUs and Overclocking
I
E6600 and P5W Deluxe Overclock Help

I've actually gotten my setup (E6600, P5W DH Deluxe) stable at 375fsb w/ 1.40vcore. The Intel thermal analysis tool does report some hot idling in the mid 40s, but otherwise it's been great. I've been using the 1305 bios version, FWIW. Oh, and water cooling. Still can't get the ram to run at...
- imported_itsmezed
- Post #24
- Sep 23, 2006
- Forum: CPUs and Overclocking
I
Warm: 250GB IDE Seagate Hard Drive $59.99 AR

I'm not sure about when you sent the rebate, but I know that for rebates under $100 they will cover it in the store if you have a denial letter and show it was a valid submission.
- imported_itsmezed
- Post #8
- Sep 11, 2006
- Forum: Hot Deals and Giveaways
I
High E6600 Temps?

Well... this last upgrade was the longest I have gone between CPU upgrades, about 2 years. So if I get that long out of it I'd be fine. At "auto" voltage I believe I had it at 333 FSB. Still, I think I will get that better Koolance block as the bottom should make better contact than this...
- imported_itsmezed
- Post #13
- Sep 2, 2006
- Forum: CPUs and Overclocking
I
High E6600 Temps?

I have the same mobo as you, DJ Mike. So does that mean when I was cranking along at 3.5GHz (390x9), 1.4625v, and seing 63-65 with both cores at 100%, that the temp wasn't actually all that bad?
- imported_itsmezed
- Post #11
- Sep 2, 2006
- Forum: CPUs and Overclocking
I
High E6600 Temps?

Room temp is 70ish. Oh, and I measured the temps with both CoreTemp and the Intel Thermal Analysis Tool. I have a feeling that I may have cut the water cooling loop a bit too long, plus having the video card in it, I don't think the CPU block I used from my old Thermaltake BigWater system is...
- imported_itsmezed
- Post #8
- Sep 2, 2006
- Forum: CPUs and Overclocking
I
High E6600 Temps?

It's a Koolance Exos external water cooling system. You can't change the radiator out. Anything better would have to be external, and then we are talking about $300+ and the cost of new water blocks. The Antec P180 case is nice and quiet, but there isn't room inside for anything else, really...
- imported_itsmezed
- Post #5
- Sep 2, 2006
- Forum: CPUs and Overclocking
I
High E6600 Temps?

Using CoreTemp and the Intel thermal analysis tool, I'm showing 40-42c idle, and that's with default voltage. It hits another 10c higher than that with both cores under 100% load. Right now, I have it watercooled using a Koolance Exos and AS5 under the water block, so you would think it would...
- imported_itsmezed
- Thread
- Sep 2, 2006
- Replies: 13
- Forum: CPUs and Overclocking

RESOURCES

Top Bottom