I just picked up a new Panasonic DMP-BD35K Blu Ray player with Ethernet port. Is there a way to connect the Blu Ray player to my HTPC for an internet connection?
My router which is DD-WRT supported (Buffalo Mimo) is upstairs on my main PC thus I can't hard wire it.
My HTPC (Vista Ultimate...
I really think the fact that my Bank Cycle Time (TRC) is being auto set @ 1 clocks is my crashing problem.. shouldn't it be more like at 16?? I read tRC - Row Cycle Time:
The minimum time interval between successive ACTIVE commands to the same bank is defined by tRC.
tRC = tRAS + tRP
ha ha now you tell me. Well I ran memtest86 v1.7 2 hours 5 passes no errors (yellow slots)
I am probably wrong. No errors thats good. Right?
You would think it would be good, however I've gotten the blue screen of death for the second time today while running BF2, and the computer just...
I set it to EXPERT and manually changed it to 2T and it still boots 1T and won't load windows.
In addition, CPU-Z reports my Bank Cycle Time (TRC) as 1 clocks... that doesn't seem right and I didn't see where I could change that in the bios.
My computer now randomly shuts off followed by a long loud tone (beeping). All I gotta say is WTF?!
I tried running my ram with SLI enabled however it defaults to 1T even when I change it manually to 2T... still posts as 1T so I disabled the SLI
I did read this and reseated my memory...
Whoa, I hadn't read this thread in a week and it took me a few hours to catch up.
Anyways, I installed Vista last night. Everytime I restart my computer it runs a memory test when booting. Any idea why this happens and how I can turn it off??
Yes, I have the "bad" CosairPC6400 C4, on...
I purchased Microsoft Optical Desktop Elite for Bluetooth (keyboard & mouse). However I cannot get windows xp or Vista to install the proper drivers. I've used the CD that came with it and even downloaded the latest software off the microsoft website. It keeps referring me to the bluetooth in...
I did use the looser timings and I have the C4
I kept my Mem @ 800 and ran my FSB @ 1595 1600 1605 1610 with no luck.
When lower voltages didn't work I cranked up as high as Vdimm 2.178 Vcore 1.5 NB 1.78 mV+100
I cranked my Silverstone 120mm fan (110 CFM) to get plenty of air.
Got all the way to 1610 with no luck. It freezes so much I can't even get in the bios sometimes and I hate clearing the CMOS because the SATA plugs & front panel plugins get in the way. Plus I have to pop a mem stick everytime because of the 1T timing default. I don't get it.
My only problem with the 0401 so far is when your clear the CMOS it reverts back to 1T as a default. I have to pop out a memory stick to get back in the bios to change it back 2T. I was actually able to get Windows to load at 3.6GHz unlinked @ 1600FSB/800Mem but it was not stable no matter how...
I figured out the problem. I selected it to save optimal defaults when I added the new bios and it made my memory 1T and it kept crashing. Set it back to 2T and now I'm good.
I loaded the 0401 bios. However, my computer will only start of I use 1 stick of RAM. Whenever I try to put my second stick back in I cannot even get into the bios. (yes both in black slots)
I have to leave tonight but will try to address the issue tomorrow, any ideas by then would be...
I was going to pick up a 1GB usb flash drive and copy the bios and flash utility. Do I need to copy windows boot files too? Will 1GB be big enough or do I need a bigger usb flash drive??
I agree the ninja is balanced and not too heavy. However I had issues with the base hitting the capcitors next to the chip and modified mine a bit see here
As far as OCing my e6600 I just couldn't get it to 3.6GHz no matter the voltage. I could hit 3.5 but is wasn't stable. For daily use I...
Thanks for the info. I'm actually on the Hardforums all the time and had seen your info. Well my chip is L625 and everyone with that chip had to go 1.5vcore to get a decent speed... so that may be part of it. Corsair has my memory rated @ 2.1v but I can play with that a bit if need be. I'll...
Ok, I've been working at getting a stable OC. I've just been running ORTHOS for about 5min. after my settings to make sure it doesn't lock up. So far I've only gotten 710/1400 it keeps locking up above that.
I understand th 1:1 ratio but how does that make things smoother? If I up my...
Yup I'm using the black slots. I tried JonDoms settings and just can't get windows to boot up @ 1600/800.. I can get to around 1580/775 but I really have to start cranking out the voltage. I can run 1500/750 @ stock voltage with the exception of my NB 1.39. So am I now running my Memory at...
Tried it with no luck. When I changed my multiplier to 7 my bios wouldn't post and I had to reset the cmos.
I have a upgraded fan cooling solutions on both the NB & SB. Plus I cranked all my fans in my case to high. I only tried those settings for a short time to see if I could hit...
Ha Ha.. Winter Storm and that shut down work today so I stayed up late.
I did loosen the timings and that did not allow me to increase my clock speeds. It was only increasing the NB voltage that allowed me to climb higher. How do I adjust my multiplier? Is that the multiplier for the CPU...
Well 900/1800 is different on a e6300 than a e6600 if that's your reference because that put's you at 3.15 GHz and I'm hitting close to 3.5GHz @ 1550. BTW, What's your temps @?
Ok right now I'm a@:
NB 1.56 Vcore 1.33 Vdimm 2.08
Temp: Cores 41&42C, Mobo 37C
FSB 1550
Mem 775 4-4-4-12-2T
As far as airflow to my Mobo, I have an Antec p180 with a front 120mm intake, and 2x 120mm exhaust back and top. It would probably be cooler with a side fan blowing directly on...
Sorry, ended up running to fry's and replaced my NB with Thermaltake Spirit II
I used these settings:
As far as numbers Set to: Unlink
FSB 1420
Mem 710
Currently downloading 3Dmark06
However it froze when I came into windows so I uped my NB to 1.39 and my Vcore to 1.35 and it's...
OK, I'm ready to OC. I have my Ram @ 2.08 4-4-4-12-2T. Mobo is bios 0202, both cores are running around 37&39C my mobo shows 37C. I can up my NB & CPU voltage but I'm unsure how to set my FSB .. linked, nonlinked, mhz etc..
& how do I test my stability?
Tnx, Core 2. I'm looking at OCing my 6600 a bit but get a little confused by all the calculations. I understand adjusting the voltages but I'm unsure about the linked or unlinked and what to set my FSB @ etc..
I recently purchased a Scythe Ninja Plus and ran into issues with the mount being obstructed by 2 capacitors. I ended up buying a $3.50 metal grinder and overcame that issue rather easily :) see link: Scythe Ninja Plus
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.