Search results

  1. R

    Networking Performance is bad until Network diagnostic is started

    thanks dnoyeb, so far I had not thought, that any powersave things could cause my problem, also it would be a good reason. My VCR is usually in hibernation mode (and often waked by WOL), therefore Powersave modes might be a reason. But now I checked, whether the network adapter has any...
  2. R

    Networking Performance is bad until Network diagnostic is started

    Hello, maybe somebody does have an idea ... I do have a small network with Notebook, Network switch and digital VCR. The digital VCR is having an onboard Intel network solution (with the latest drivers installed). Very often I do have really bad networking performance (netIO shows 100kByte/s...
  3. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    It is getting more and more clear. a friend pointed me the the datasheet of a southbridge with integrated RTC, and finally I found all the registers mentioned in the ACPI Spec in Hardware. But this would mean, that if I'm rewriting the RTC_En bit, and then switch off the PC (no chance to...
  4. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    Hi Sao, the quote I made was from this spec ... and the information based on RTC registers ist from a TI RTC datasheet. But as I mentioned before, I'm to stupid to map the Spec to a Hardware schematic. :-( I'm used to hardware related DRAM/chipsetspecs specs. This one is a level to high...
  5. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    HI sao, thanks for the answer. In principle this goes in the right direction, but there is one problem in your argumentation: You mention, that the BIOS checks the memory location somewhere. But the BIOS is not active at the time a wake up event occurs. I have checked the ACPI spec a little...
  6. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    H sao123, I aggree with you, that the shutdown is different, but this does makes no difference at the time a wake up event occurs when the system is in S4 or S5 mode. this information written to the HDD is checked and used after the BIOS boot to decide whether the OS has to boot, or the system...
  7. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    Hi Peter, thanks for the response, but I don't think, that in S4 anything more than in S5 is powered. You can dissconnect Power when the System is in S4 reconnect it, and the system is booting from hybernation mode without problems. On my notebook I do even change my HDD to boot different OS...
  8. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    Sorry for the other post. Don't really know what happened there! Hermann
  9. R

    MoBo Designers and BIOS Programmers: Difference between S4 and S5 for WakeUp event

    Hello, I asked this question already once, and got no answer. Maybe I'm more lucky this time. The WINXP Task Scheduler is able to wake up my PC from S4 (Hybernation mode). But at the time the Wake up event occurs the system state is the same then in S5 (Soft off). The only difference between...
  10. R

    MoBo Designers and I

  11. R

    Difference for Wake up from S4 vs. S5 ???

    Hello, short but (I assume difficult question): Why is it possible, that e.g. the task scheduler wakes up the system from S4 (hybernation, suspend to disk) , but not from S5 (soft off) state ???? In both cases the system is powered down completly, you can disconnect the power, and after...
  12. R

    How does the Task scheduler (WINXP) wake up my system from S3? or How to wake my system from OFF or Hybernation state ?

    Sorry, I didn't wrote detailed enough about what i wanted to know! I would expect, that the RTC is having some registers, that can be programmed. If there is the event in the RTC, which signals are activated, and where are this signals evaluated (south / Nothbirdge are not powered up in S3)...
  13. R

    looking for a Micro ATX Case with Full Size AGP and PCI slot!

    Hi all, I'm looking for a micro ATX case for a HTPC. But usually the uATX cases to only have one or two PCI slots with a riser card. Does anybody knows a nice small case that supports full size AGP and PCI cards ? Basically I just don't like the hight of a usual desktop, thats the reason, why...
  14. R

    How does the Task scheduler (WINXP) wake up my system from S3? or How to wake my system from OFF or Hybernation state ?

    Hi all, it's some time ago since my last visit. Lets take a look wheter the forum is still as good as it was ... I'm buliting a Home Theatere PC. As I do not want to leave it on all the time I tried to wake it from different power safe states. S1 is no Problem! Wake up from S3 is working on...
  15. R

    Article: "RAM explained"

    Nice article about DRAM: Ram explained
  16. R

    Rambus vs. Infineon : trial ended ?

    link to anohter forum where the news from Friday are disussed: Discussion about Rambus trial bye ruckb
  17. R

    Which is best memory brand?

    Hi KingOfComputers, thats the reason, why i normally talk about 64Mb x8 organized devices. I normally do not use just the numbers, I try to put this numbers into words. I expect this is easyer to understand then 8x8 or 16x8 as there is no explanation, what this numbers mean. As long as somebody...
  18. R

    Which is best memory brand?

    Hi KingOfComputer, I don't think that I have said anything different, I just gave an example how a 128MB DIMM can be built. If you want to give an exact definition you have to consider, that you can use x4 devices to built up a DIMM with 16 64Mb devices that is single sided (even if it has...
  19. R

    Which is best memory brand?

    HI, there are several things you have to reconsider when asking about a good brand for memory. The first thing is the SPD programming. If this is done wrong, then your system can have a lot of problems with the automatic DRAM timing settings. I have read several tests of main memory, that...
  20. R

    1GHz Slot P3 on Gigabyte 6BXU

    Hi I would like to use a 1 GHz Slot1 P3 coppermine in my Gigabyte 6BXU. But the manual only talks about P3 up to 600MHz. Several questiones: Does anybody knows whether this will work? Are there diffent cores whith differen voltages that my cause problems? Will there be any BIOS Problems with...
  21. R

    MS knows WIN2k disk cache Problem, but is not releasing the fix!

    Hi, i have just found the solution to a problem that I have in the MS databases, but MS is not releasing the FIX. As in earlier versions of WIN98, when the shutdown was done too fast, the disk cache was not written to the harddisk and the data was lost, is now a problem, that the diskcache is...
  22. R

    Problems with Maxtor 40GB Harddisk under WIN2k and Write Back cache Enable

    Hi, I have found something about my problem in the MS database. Microsoft knows the Problem, but is not releasing the fix. Look at synchronize cache Problem Is anybody having the Classpnp.sys from 01/04/2001 and the Disk.sys from 01/15/2001 ?? thanks ruckb
  23. R

    Problems with Maxtor 40GB Harddisk under WIN2k and Write Back cache Enable

    Hi, I have the problem, that my WIN2k is sometimes doing a scandisk, although the system was shut down normally. Last time I lost a WIN2k installation because of a defect registry. Again, the shutdown before was OK. I have one hint, that maybe the Shut down is to fast, and the cache is not...
  24. R

    Is ECC SDRAM faster or slower than regular SDRAM?

    Hi, although most of the people say, that ECC is only needed for servers, I think that it is a good thing for overclockers. Most fails for OCed memory I have seen so far are single bit fails (maybe for tRP reasons), and even if the normal operation for ECC is aout 2-3% slower (and a real...
  25. R

    Poll: DDR Really worth it? (Updated)

    Hi, as WildCoyote said: Doing step by step for getting faster! Not only one thing makes the speed of a system. 10% faster memory, 5% faster harddisk, 15% for the new graphiccard, 20% for the new processor, and you have a new high speed system. Memory is only one thing, but it is neccessary...
  26. R

    Worth getting Registered ECC RAM over Unbuffered Non Parity?

    Hi MedRat, take a look at the link I gave above. ECC is a little bit slower then non ECC ! ruckb
  27. R

    Worth getting Registered ECC RAM over Unbuffered Non Parity?

    Hi snowPatrol, check this thread, there is a lot of info included: ECC Thread ruckb
  28. R

    Which DDR RAM to buy?

    HI, the PC1600 spec is a 100MHz FSB. Therefore a cycle time of 10ns. But most of the chips should be already -8, and therefore even tested to a tck of 125MHz. I have tested DDR modules, that are doing PC2100 at 222 without problems. the most critical parameter was tRP, that caused some single...
  29. R

    Which DDR RAM to buy?

    Hi Mysterio, I don't know, why many people are thinking just because of using a 33% faster memory they will have a 33% faster Computer. There are some benchmarks, that show this high performance increase for DDR compared to SDR, but most of the benchmarks show a performance increase from SDR...
  30. R

    Anybody using AIMM (GPA) Memory with integrated Graphics controller (e.g. i815)

    Thanks boomerang, you gave me at least some hint about it. My problem is, that I have a AIMM, but it shows up nowhere when it is in the AGP Slot. Therefore your comments showed me that it should be already recogniced. I aggree with you, that I expect no real performance boost from it! But I...
  31. R

    PC133 DIMM's backward compatible with 66mhz bus?

    Hi, I do mainly aggree with the yes, but not so completly. As the access time from clock was getting shorter for PC133, on bad designed PC66 Systems you can run into problems with the Hold time of the data (tOH). If the system is strobing to late, then the data are not valid any more. This is...
  32. R

    Anybody using AIMM (GPA) Memory with integrated Graphics controller (e.g. i815)

    Nobody ??
  33. R

    Which DDR RAM to buy?

    Hi, Do you have a 133MHz FSC Processor ? If not, then take the PC1600, because, the mem bandwith don't helps to much, if you can not get it to the processor! Do you have any closer spec to the DIMMs? Normally, the PC2100 will run as 2.5-3-3, and I expect the PC1600 to run as 2-2-2. Therefore...
  34. R

    Anybody using AIMM (GPA) Memory with integrated Graphics controller (e.g. i815)

    Hi, I'm looking for informations about AIMM Memory. E. G. should the i815 recognice a AIMM memry module wile booting? Does it have to be enabled ? .... Can somebody help me there with some information or some links. i'm somehow to lazy in the moment to check all datasheets ;-) thanks ruckb
  35. R

    Testing RAM

    Hi, i have tested several programs, and the best I have seen so far are memtest86 (link was already given in a post earlier) and the Goldmemory. the link was www.goldmemory.cz (can not link it directly, as no JAVA / ActiveX is enabled, don't know what is needed to make the http button above...
  36. R

    Is ECC RAM Better than PC133 SDRAM (Cas2)

    Hi, in the meantime I found at least one reason, why ECC Memory is slower then non ECC. There are done partial writes to the memory to. Therefore the datamask pin is used to write not the complete 64 bits to the DIMM. But if you are using ECC then The ECC value has to be calculated from all 64...
  37. R

    Is this PC133 256mb CAS 2? Where can I look to find info on it?

    Hi, excuse me, I didn't realized, that the link was a ftp link ctSPD The page for the SPD readout link was: http://www.heise.de/ct/ftp/ctspd.shtml If the link was not working try this. -7.5 is no indicator for CL2 or 3. It means just, that the max. clock frequency is 133MHz. The 6 layer...
  38. R

    Is this PC133 256mb CAS 2? Where can I look to find info on it?

    Hi, you know, that it is normally not possible to answer your questione with this information ! Normally I'm using all different search engines and just type in some parts of the markings. But Metacrawler found nothing, so I don't want to spend so much time. But you can still try !!!!! The...
  39. R

    Is ECC RAM Better than PC133 SDRAM (Cas2)

    Hi Mushkintechs, thanks for the flowers, but I have already a good job ;-) for the links I'm using normally the Internet pages of the manufacterers. e.g. for the information about the capacity on the DIMM i used a datasheet from Infineon DIMM datasheet On page 5 is the blockdiagramm...
  40. R

    Is ECC RAM Better than PC133 SDRAM (Cas2)

    Hi MushkinTechs, interesting thoughts, but I can only partly aggree with you. addidional capacity on bus: The DQs are just on its own, so no added Cap. The clocks are a little bit more complicated. The unbuffered DIMMs are getting 2 clocks for SDR (3 for DDR). But if you have a non ECC DIMM...
COMPANY
RESOURCES
FOLLOW
Top Bottom
sale-70-410-exam    | Exam-200-125-pdf    | we-sale-70-410-exam    | hot-sale-70-410-exam    | Latest-exam-700-603-Dumps    | Dumps-98-363-exams-date    | Certs-200-125-date    | Dumps-300-075-exams-date    | hot-sale-book-C8010-726-book    | Hot-Sale-200-310-Exam    | Exam-Description-200-310-dumps?    | hot-sale-book-200-125-book    | Latest-Updated-300-209-Exam    | Dumps-210-260-exams-date    | Download-200-125-Exam-PDF    | Exam-Description-300-101-dumps    | Certs-300-101-date    | Hot-Sale-300-075-Exam    | Latest-exam-200-125-Dumps    | Exam-Description-200-125-dumps    | Latest-Updated-300-075-Exam    | hot-sale-book-210-260-book    | Dumps-200-901-exams-date    | Certs-200-901-date    | Latest-exam-1Z0-062-Dumps    | Hot-Sale-1Z0-062-Exam    | Certs-CSSLP-date    | 100%-Pass-70-383-Exams    | Latest-JN0-360-real-exam-questions    | 100%-Pass-4A0-100-Real-Exam-Questions    | Dumps-300-135-exams-date    | Passed-200-105-Tech-Exams    | Latest-Updated-200-310-Exam    | Download-300-070-Exam-PDF    | Hot-Sale-JN0-360-Exam    | 100%-Pass-JN0-360-Exams    | 100%-Pass-JN0-360-Real-Exam-Questions    | Dumps-JN0-360-exams-date    | Exam-Description-1Z0-876-dumps    | Latest-exam-1Z0-876-Dumps    | Dumps-HPE0-Y53-exams-date    | 2017-Latest-HPE0-Y53-Exam    | 100%-Pass-HPE0-Y53-Real-Exam-Questions    | Pass-4A0-100-Exam    | Latest-4A0-100-Questions    | Dumps-98-365-exams-date    | 2017-Latest-98-365-Exam    | 100%-Pass-VCS-254-Exams    | 2017-Latest-VCS-273-Exam    | Dumps-200-355-exams-date    | 2017-Latest-300-320-Exam    | Pass-300-101-Exam    | 100%-Pass-300-115-Exams    |
http://www.portvapes.co.uk/    | http://www.portvapes.co.uk/    |