Well for lug nuts I always use 6 point sockets the main reason is the torque involved and most of the time I use an impact so 6 point sockets dont round or strip the nuts.
But for all around use on other nuts and bolts 12 point are ok. But I will say that most of my sockets both SAE and Metric...
Ok have you tried it with just 2 of the subs...? If not then do so and try it with both pair (seperate) this will ensure 2 things 1 that your amp will run both pair of subs next is one of the speakers bad...? Let us know...
Yes it can... Lighting can do strange things so it is possible... Had a tractor in a barn that would not start after the barn was hit by lighting and even had to replace the battery, alternator and starter and all of the lights on it... So to me it is possible... ;)
"4.6? What engine is that? The 4.8 is LS based so no, it won't swap to a 454."
Oh yes they will... Back in 2000-2001 I had a 1969 C10 with a 427 cui BBC and put a set of 1994 drive brackets on it... Just a bit of work and everything fit perfect... I will do some checking to see where I put...
It would depend on where it broke...? If it were out at the "wheel/hub" assembly then yes it can cause an issue but until you take it apart and inspect it then there is no way to know... It might affect the bearing but should be about it if anything... Also yes it can at the transmission as...
Not sure but my Duramax is a 2004.5 but the earlier years 2001 and up are the same (had it now for a little over 10 years) :D... Very smooth except when they have issues... Ford I think they got it together around 1999 or so...? Dont know on Dodge...?
fuzzybabybunny... I drive a Duramax and it is smooth as silk and quiet when running but being a 3/4 ton truck it rides like heck as compared to a 1/2 ton or a car... Like LTC8K6 said the newer tech diesels run alot smoother than older ones did for sure... Heck I remember a place where I...
Also he may have blown one and I say 1 of the fuses of the new aftermarket radio and this will keep it from coming on as well... There should be 2 and with some radios 3 fuses and if one is blown then it wont power on...
But also as Meghan54 was telling you the underhood fuse is most likely...
Fuse...? Their are no fuses on the spark plugs...? Like I said just pull the spark plugs and spin it over a few times then replace them and fire it up...
Nah it should be ok if you did not spray to much in it...? Also if you did spray a ton in there just pull the plugs and spin the engine over several times to clear it out... But it is not needed to spray carb cleaner in a fuel injected engine...
Wait you had the the manifold off...? The...
First off my AR57 which is very cool with a 50 round mag on it... Next my Sagia 12 with its 5,10 & 20 round rotary mags... :D Then I can say my AR15 Bushmaster XMI5-E2S which has an 11.5 inch barrel with a 5.5 inch muzzle brake... Just a few...
I think "Gardener" has the right idea on the excessive vibration... I too think you bent the driveshaft so it would be toast... :(
"Good advice to check for a bent driveshaft before proceeding."
Ouch...! Looks to be about $3500-$5000 in damage to your van, dude that sucks... But it happens heck I am waiting for one to jump out right in front of my truck... Just yesterday some young guy on the highway in front of WalMart at a light hit me in the rear of my truck with a Jeep but sorry...
Now that was a very cool and calm way to handle things an awesome girl ;)... A very very good find "Thebobo"... Gotta hand it to the employees they took great care in the situation...
Hummm...? 70 miles a day is a pretty good little trip even for a car with less miles on it...? If you buy it I would consider keeping it for only a couple of years tops due to its miles...?
Main things I would look at are the CV axles/boots and would take a code reader along (so when you test...
Skel... Uhm did you not see him at the beginning when he popped it down on the base...? Might be a dummy round but might not be...? Just a bit stupid if you ask me...?
Now back on track...
Dunno but I have a live 50 cal sitting on my desk right next to me and would never do that...? Now the rest of the video is good but that just all but sunk it for me...
Guy is stupid for one thing he slams that 50cal shell down on his desk like he knows what he is doing...? DOH...! Damn wish there was something kinda small on his desk to let him know not to do that crap... Sorry shorty but did not even watch the rest of the video... o_O
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.