Search results

J
CPU Fan RPM

Hi, both the BIOS and HW Monitor show the same speed, avg 3000rpm
- jscedaz
- Post #3
- Jan 23, 2009
- Forum: CPUs and Overclocking
J
CPU Fan RPM

My artic freezer Pro 7 fan is running at 3000rpm and the box it came in only states its supposed to run up to 2600rpm is there a chance leaving it at this speed could damage it? I noticed it slowly creeps up to 3000RPM over a course of a week. Thanks
- jscedaz
- Thread
- Jan 22, 2009
- Replies: 2
- Forum: CPUs and Overclocking
J
I gone and bent some 775 socket pins :(

I haven't sent it back yet, I took your advice and did fix the pins but using a small sewing needle, the pins are straight but the metal below it still looks kind of off, but they shouldn't say anything about it because the pins are now fine and I put a cpu in to straighten it out a bit further...
- jscedaz
- Post #4
- Dec 22, 2008
- Forum: Motherboards
J
I gone and bent some 775 socket pins :(

What made it dead before this happened was continuous power cycling then complete failure were the pc would not power up. I tested the processor in another computer I then tried different ram combinations, tried another power supply even reset the CMOS one of the first things i did, it started...
- jscedaz
- Post #2
- Dec 22, 2008
- Forum: Motherboards
J
ABIT CLOSING doors for good..

They said they would honor the warrantys for 3 years after closing.
- jscedaz
- Post #32
- Dec 22, 2008
- Forum: Motherboards
J
Best MOBO / Processor combo???

And the higher numbers make us feel good :)
- jscedaz
- Post #4
- Dec 21, 2008
- Forum: Motherboards
J
Vista 64bit, 6 gigs ram, 85% memory used at idle???

Is your page file still enabled? Lots of software out there cause problems with the vista pagefile completely disabled me personally when using high amounts of ram like that I still keep a pagefile on to avoid memory low errors and general software related issues.
- jscedaz
- Post #9
- Dec 21, 2008
- Forum: Windows
J
Reliable, Solid Intel board

I was using an Asrock P43R1600 Twins which cost me around £62 which peformed great, it has 4x DDR2 slots and 2x DDR3 slots for future upgrade and supports a large variety of dual and quad processors for future upgrades. Motherboard Overview...
- jscedaz
- Post #10
- Dec 21, 2008
- Forum: Motherboards
J
ABIT CLOSING doors for good..

Damn I never did have an abit motherboard but I know they made good ones :) sad news this is.
- jscedaz
- Post #25
- Dec 21, 2008
- Forum: Motherboards
J
I gone and bent some 775 socket pins :(

Hi I'm sending a motherboard back for RMA because it died on me and my hand went and slipped and my nail bent 2 of the socket pins, i'm now worried that when the recieve it they might use it as an excuse to not go through with replacing the already very dead motherboard has anyone had any...
- jscedaz
- Thread
- Dec 21, 2008
- Replies: 3
- Forum: Motherboards
J
Memory/mobo problems please help

Hi again, thanks your help I'm going to get a new motherboard as suggested to solve the problem thankyou :)
- jscedaz
- Post #5
- Dec 20, 2008
- Forum: Memory and Storage
J
Memory/mobo problems please help

Hi thanks for replying I bought two packs of XMS2 memory so I have two packets one I begun the process of RMA but it's looking like its not the memory thats at fault. I have tried multiple combinations and have mixed it up a bit trying different slot combinations with dual channel set up and...
- jscedaz
- Post #3
- Dec 19, 2008
- Forum: Memory and Storage
J
Memory/mobo problems please help

Greetings, I hope you can help me Core2duo e6320 DFI 965P infinity-s Geil 2x1GB pc6400 (4-4-4-12) ECS 8800GTS 320MB Corsair HX520W Windows Vista 64bit (SP1) Above specs have been working 100% for 2yrs. The problem is attempting to add Corsair XMS2 2x1GB pc6400 (4-4-4-12) so that I...
- jscedaz
- Thread
- Dec 19, 2008
- Replies: 4
- Forum: Memory and Storage

RESOURCES

Top Bottom