Search results

  1. Low speeds with Comcast but good signal strength.

    Yeah I type awful. That's what I work on cable and not computers LOL. You'd never know I used to do data entry, query management and some minor programming. Anyway, the device you listed looked like a dory model, which has an internal router with wireless [Arris TG862G], so I wanted to make...

  2. Cable tester

    I belive the part is only needed for IDENTIFING cables, IE go to office 1, plug identifier in port, then go to patch panel and start pluggin wires in to meter, when it identifies the probe you left, you found that wire. The rest of the time its looking for shorts, opens, or lengths based on...

  3. Low speeds with Comcast but good signal strength.

    Your upstream is too high. 51 or lower, might just be the heat probalby need to adjust the thermal gain in the line amps again, but tha'ts not where it needs to be for D3 upstream channel bonding. Is that dory in bridge mode too BTW? I t needs to be otherwise you'll double and that can be a...

  4. Can you use cables to extend wifi antenna?

    You can not only buy antennas with cables you can buy powered antenna with a signal booster internal to them. It depends on your router, but generally the high frequency waves of wireless services passes through standard dry wall fairly easily its denser and conductive materials like concrete...

  5. Reliable modem and router recommendations for Comcast internet please

    most people consider them trash but it depends on WHAT YOU NEED in a router.

  6. Reliable modem and router recommendations for Comcast internet please

    the moto is solid, netgear is generally considered low end trash if it works for you great, but don't expect it to. The trick on the moto 6141 is it supports 8 downstream channels depending on what comcast speed you are subscribing too this may be overkill, but if your not needing a cheaper...

  7. Can't reach Microcenter.com for last two days.

    now it works on my comcast, last time it sat there for maybe 2 minutes and timed out but loaded right up this time.

  8. Can't reach Microcenter.com for last two days.

    Not loading for me, I am on Comcast in the north west. won't ping either, resolves to 66.194.187.21 > nslookup www.microcenter.com Server: microcenter.com Address: 66.194.187.21 Aliases: www.microcenter.com DNS request timed out. timeout was 2 seconds. DNS request timed out...

  9. Old network cables not working cause of dust ?

    By dust do you mean like house hold dust or do you mean green or white colored powder, becasue they are not the same thing. The powder comes from exposure to water or different metal types and is corrosion. The only thing you can do is replace the parts with the correct types. The more likley...

  10. Laptop refuses to find wifi signals

    I have no idea about the wifi stick I just assumed that was a windows 7 driver issue or he did not disable the onboard wifi in device manger so windows was still trying to use the internal.

  11. TWC Modem/Router recommendations

    http://www.timewarnercable.com/en/residential-home/support/topics/internet/buy-your-modem.html

  12. Using your own modem with Comcast

    The policy is you can buy your own eMTa but there are stipulations. It was that best buy was selling them but they claimed it was not worth the inventory space becasue they sold so few. Yes the arris TM-822 [not 822G it may be supported but, you can also check eth comcast supported device...

  13. Laptop refuses to find wifi signals

    There are usually an on off switch around the edge AND/OR an FN Number key combo that turns the radio on or off. The only other thing is sometimes windows updates do stupid things like set the power saving modem when on battery to turn wireless off so it will show up when AC power is on but not...

  14. Is it possible for WiFi to have an "unclean signal"?

    Without addressing your specific issue, yes it is possible to have unclean RF signal no matter what the source is. Distortion from over amplification is a bad thing except in the world of rock n roll music. I work on coax all day everyday and the craziest things can cripple the entire RF...

  15. Is there a saying or rhyme to remember the color order of cat 5 cable?

    Depends on what you mean, there are different color orders for phone versus Ethernet. And even in Ethernet there are different standards as I recall.

  16. Any way to test your network "locally" the way it is seen "remotely".

    VPN?

  17. Question regarding CAT5E shielding with a particular wall socket

    You do realize you cannot just hook the shield up to a plastic outlet cover and be bonded to the ground system of the building right? I don't think you would bond the shield at the outlets personally, I believe it would be more likely to be done at the distribution point, which I am guessing is...

  18. Net Neutrality in Harm's Way!!!

    You ever heard of the boy who cried wolf? http://www.dslreports.com/shownews/ISPs-on-Net-Neutrality-Ruling-Dont-Worry-Trust-Us-127334

  19. Net Neutrality in Harm's Way!!!

    Sigh such drama queens.... Its not the end, the existing rules were not with authority due to the FCC not having that actual authority to make them. If your local sheriff said everyone has to be home by 8:00 PM you'd probably challenge his authority to do so too. So now they question is who...

  20. Surfboard SB6141 Not Working with MoCA

    So you don't let the moca carriers into the cable system outside and cause havoc on their network forcing them to disco you. AS long as that filter is before the tap and all devices come after it, its done correctly. The question is then what frequencys his moca on, becasue some are on cable...

  21. What does Comcast use for testing ingress?

    Depends. At the individual house, I use my Signal level meter, spectrum analyzer option. We also have some new software that uses wave theory of reflection to look for impedance mismatches [called flux, see after this typing where I link an old bell labs video on wave theory], which is where...

  22. Motorola SB6141 bricked?

    Are you sure its not just acting like a switch until it connects and is then acting like a bridge? can you see the signal levels at 192.168.100.1 when its connected? Couple of moto modems enable a DHCP server for some unknown reason when they do not have a connection, but once they are...

  23. Cat5 junction box question

    I am guessing you have a smart panel where the lines go to standard punch downs and have a RJ-45 port near them, this is a sort of patch panel or you are looking at phone and not Ethernet wiring [both use cat5e in the modern day, just depends on what/how you connect them, on the ends. Pictures...

  24. On-Q LeGrand Home Network -- Need Help Please!!

    Eww a directional coupler, what are your cable modem levels, out of curiosity. [192.168.100.1] ? Also for clarity, if you have a cable modem and not a cable gateway [gateway = modem + router in one piece] then you need a ROUTER immediately after it before YOU USE A SWITCH. Just for clarity.

  25. Motorola SB6141 bricked?

    That is a docsis 3 modem, they are very signal picky, you probably need a tech visit to balance your signal levels, to be honest. I work for comcast, this is not an uncommon issue for home self wiring jobs. Popele think thay cna just plug them into any coax outlet in the house, it does not...

  26. Random, intermittant, daily Internet problems

    192.168.100.1 if you can bring that up post signal levels and error logs of the modem my suspicion is this. The cable modem is out of spec and needs a cable installer to repair your set up, so the modem reboots, when they happens the linksys G routers were NOTORIOUSLY picky about losing their...

  27. LTE modems

    Becasue you will be locked down to one cellular carrier and it will cost you about an additional $100-$200 for the laptop over one without it? Mifi's and LTE usb modems are like $35- $50. Its just not economically intelligent in this country. Maybe if they did not lock them down to one...

  28. How ADSL2+ and VDSL2 are different?

    Are you talkign about adsl or adsl2+, i did no tthink too many telcos went with ADSL2. ADSL2+ - http://en.wikipedia.org/wiki/Asymmetric_digital_subscriber_line_2_plus ADSL2 - http://en.wikipedia.org/wiki/Asymmetric_digital_subscriber_line_2 VDSL2 -...

  29. Is my neighborhood slow, or am I killing my router?

    http://www.myaccount.charter.com/customers/support.aspx?supportarticleid=2615

  30. Don't have option to put in password for wifi connection

    No. Right click the network symbol on the lower left of your screen and select network and sharing center from the pop up. A new window will open on the left hand side is a list, once of them will be Manage wireless networks if wireless is enabled on the computer. Click that link. New window...

  31. Don't have option to put in password for wifi connection

    Go to the wifi network list and clear out all the entries for that device, remove them. then try to reconnect to the device it should not recognise it and ask for a pass phrase again.

  32. Changed modems/router, no internet, pls help me deny Comcast $7/mo

    So you need to CALL comcast and tell them you BOUGHT your OWN modem, they will ask you for the MAC address and MODEL. Until you do this ,you modem is an unknown device trying to connect to the comcast network, but will be denied. Last I saw Motorola calls their mac the HFCMac, but cable mac, or...

  33. Best of both worlds?

    If you don't rerun that damn cable I'm telling skynet to start looking for packet losers. Seriosuly, your not getting anything out of running two connections to one computer off the same ISP. RERUN THE CABLE. Why pay for a load balancing hardware, add complexity pointlessly to your setup, when...

  34. Using your own modem with Comcast

    You need a D3 modem if your PAID FOR BASE SPEED is greater than 30 Mb/s, otherwise a D2 will work fine. The newest concern is when will you be forced to go IP6 though, so make sure if you buy a new modem it does support IP6. That seems to be the line they drew for what D2 modems will be EOL and...

  35. When will my DOCSIS 2 no longer work?

    When your cable company requires channel bonding, and unless I miss my guess that will be some time down the road. As to whether to get a new modem now, 30 is about the max for a D2 device, if you subscribe to a faster internet package than 30 Mbps, then upgrading to a D3 modem will allow you...

  36. Using repeater for credit card machine

    3 plausible options. several possible, but plausible is the key. One run a coax cable underground to the building [you can bury it only a few inches or go gung ho to 16" and put in pvc conduit, whatever you want] and tag both the existing coax in use [for the modem] and the one you run, every...

  37. Changing Modem Router Settings Wirelessly. Bad?

    Depends on the situation if its your house go for it just don't call the isp and say I did something and can not get on wireless anymore fix it or expect to pay a charge, as you should. If this is for the DOD, don't be a fuckhead, wire in, disable that feature and pull your head out of your...

  38. Comcast cable internet questions?

    So there are 3 cases where you have more than one cable modem 1. Multiple accounts in the same residence, usually you must change the address slightly like 123 1/2 a street or 123 a street, ofc, somecity, somestate this is usually done when running residential and business to the same address...

  39. Comcast cable internet questions?

    That's actually area dependent, I work for the company and my free speed was 12, then 25, got upgraded to blast which is now 50, and my speedtest pops 60/11 right now, but the 105 was always area dependent and we NEVER had blast with it. Truth me known the head end techs set the cmts up wrong on...

  40. Comcast cable internet questions?

    1.) my comcast provided (rental) wifi router/modem combo has 4 downstream bonded channels and 3 usable upstream channels. So from this I figure I have around 152Mbps total download bandwidth and maybe 30Mbps total upload bandwidth. My wifi usually maxes out around 25Mbps to 42Mbps download...
COMPANY
RESOURCES
FOLLOW
Top Bottom
sale-70-410-exam    | Exam-200-125-pdf    | we-sale-70-410-exam    | hot-sale-70-410-exam    | Latest-exam-700-603-Dumps    | Dumps-98-363-exams-date    | Certs-200-125-date    | Dumps-300-075-exams-date    | hot-sale-book-C8010-726-book    | Hot-Sale-200-310-Exam    | Exam-Description-200-310-dumps?    | hot-sale-book-200-125-book    | Latest-Updated-300-209-Exam    | Dumps-210-260-exams-date    | Download-200-125-Exam-PDF    | Exam-Description-300-101-dumps    | Certs-300-101-date    | Hot-Sale-300-075-Exam    | Latest-exam-200-125-Dumps    | Exam-Description-200-125-dumps    | Latest-Updated-300-075-Exam    | hot-sale-book-210-260-book    | Dumps-200-901-exams-date    | Certs-200-901-date    | Latest-exam-1Z0-062-Dumps    | Hot-Sale-1Z0-062-Exam    | Certs-CSSLP-date    | 100%-Pass-70-383-Exams    | Latest-JN0-360-real-exam-questions    | 100%-Pass-4A0-100-Real-Exam-Questions    | Dumps-300-135-exams-date    | Passed-200-105-Tech-Exams    | Latest-Updated-200-310-Exam    | Download-300-070-Exam-PDF    | Hot-Sale-JN0-360-Exam    | 100%-Pass-JN0-360-Exams    | 100%-Pass-JN0-360-Real-Exam-Questions    | Dumps-JN0-360-exams-date    | Exam-Description-1Z0-876-dumps    | Latest-exam-1Z0-876-Dumps    | Dumps-HPE0-Y53-exams-date    | 2017-Latest-HPE0-Y53-Exam    | 100%-Pass-HPE0-Y53-Real-Exam-Questions    | Pass-4A0-100-Exam    | Latest-4A0-100-Questions    | Dumps-98-365-exams-date    | 2017-Latest-98-365-Exam    | 100%-Pass-VCS-254-Exams    | 2017-Latest-VCS-273-Exam    | Dumps-200-355-exams-date    | 2017-Latest-300-320-Exam    | Pass-300-101-Exam    | 100%-Pass-300-115-Exams    |
http://www.portvapes.co.uk/    | http://www.portvapes.co.uk/    |