I am thinking of buying a handsping prism and want to make a good investment. Want to make sure that i will use it. I am a supervisor at a Plant. Will this be a helpful product for to own. THX!!!!!!!!!!!
I have a P3 800 with Vcore of 2.05 at 1080 and it has been running for three mouths. I do have a 72W Peltier. Temps are 1c at idle and 32c at full load.
In my case my P3 800 will run at 1066 but when i play MCM2 of other games it locks because of temp problem. I know then because my temp goes up 2 more deg. then befor when it goes that high it locks so this will help. I have a CD Rom a CDRW and IBM 30G HD that is alot for one power supply when i...
I am geting a 72W pelitier Kit and i am also going to get a seperate power supply for it. What i need to know is how do I get the power supply to power up when it is not connected to the motherboard. ( you know the power can be on to the power supply but the fans don't run till u hit the ON...
Make shore that u run 3d mark 2000 in 3D TL Hardware under options.Not P3 or solfware TL.I have been working with my freinds computer for the same problem. but he had a GF MX card and only scored 2247. he also has cel 600 at 945. your 3D Marks may not have the 3D TL Hardware sitting because i...
It is a PCI MX card so was the Voodoo 3 3000. i put alot of computers together using the cusl2 motherboard, but i always use AGP slot i went throw the bios and everything there looks right. it is set to PCI vga and onboard is off. drivers D 6.34 blaster.
which should benchmark better on 3dmarks 2000. Voodoo3 3000 benchmarked at 3268 and the pci gforce 2 MX at 2238 on a asus cusl2 with celry 600 at 936. HELP HELP HELP!!!!!!!
I just bought a SamSung SyncMaster 900NF and it is very clear and has a very high refresh rate at 1600*1200 it has a refresh rate of 87hz at 1024*786 the refresh is 132hz. got it for $380 from Netop, Inc. Tel-201-392-8877. They are in NJ.
It is a aperture grill monitor with a Dimondtron Flat Tube.
Same here mine is running 1066 with air cooled Alpha. look at my specs below. V/core 1.80 125\125\41 sys is very stable run 3DMarks loop for 12 hours. temp is below.
I have the 6035 with Delta 38 and it rocks it is not that loud and it cools great. and i can't not hear it over the 8 other fans in my case.look at my specs and see what it did for me. Stable sys at that.
I have the 6035 with Delta 38 and it rocks it is not that loud and it cools great. and i can't not hear it over the 8 other fans in my case.look at my specs and see what it did for me. Stable sys at that.
I have the 6035 with Delta 38 and it rocks it is not that loud and it cools great. and i can't not hear it over the 8 other fans in my case.look at my specs and see what it did for me. Stable sys at that.
The CUSL2 must go to 1/4 divd when your bus speed is 125fbs becuase I ran 3DMark 2000 and did not lock up one time for an hour.Vot is set to 1.80 this board kicks but.My harddrive is not working hard if it didn't switch the divd to 1/4 I don't think that it would run at all.
I have a BE6-2 ABIT mother and i would like to thave 256mg pc133 cas2 ram in it. What way is better for overclocking 1 stick of 256 or 2 sticks of 128. I was gone to buy Mushkin for $159 for 128mg pc133 c222 but Crucial has there 128mg for $91. What way would you go. I also heard that some...
Thanks ALL
---
Razzer,
Your emailed subscription updates are being returned to us with the error message,
Your message was not delivered within 1 days.
Host pennswoods.net is not responding.
These returns clog our mailbox, so I have cancelled your current subscriptions. Please notify your...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.