Search results

  1. A

    Does p4p800 non-deluxe come with WinDVD in US?

    Thanks for the reply guys! I was afraid that the non-deluxe would not have it here in the states. On another forum a guy in Europe said his had it. Hey, they also got the p4c800 non-deluxe a while back! They must know somebody or somethin' I guess this gives me another reason to get the...
  2. A

    Does p4p800 non-deluxe come with WinDVD in US?

    I know this is a trivial question, but I find that the Asus website refers to a "Gold version" of this board with the WinDVD Suite, and implies that there are other versions that do not have the disk. I have not seen "Gold" mentioned on the various retail vendor's websites and I did see some...
  3. A

    XP - Can this really be progress???

    Thanks again to all for trying assure me that XP is what it was cracked up to be. I fully agree that my mistakes have probably caused a lot of my trouble. Unless DirectX9 falls in the category of bad upgrades, I haven't changed any drivers from the original install other than installing...
  4. A

    XP - Can this really be progress???

    Nothinman, Right you are! I kept the old disk and did a direct file transfer. Problem with that is that I now need to disconnect the old drive since I can never be sure XP is not writing over the old drive. (I have only had that happen once since I did the files/settings transfer, but a lot...
  5. A

    XP - Can this really be progress???

    To those thinking of upgrading to XP: After a good deal of reading, I decided to upgrade to XP from Win98. Supposedly I would enjoy better drivers, a greatly improved operating system and one far less prone to failure. Some people virtually glowed with satisfaction from the bullet proof...
  6. A

    Okay, I am a dunce! Win98 to XP on new disk???

    Probably not software that you would know, ... a dos based technical wordprocessor EXP from many years ago. It was upgraded to a Windows program that was not quite as useful in early versions. I have pretty much moved onto a more improved total windows based solution, but one must understand...
  7. A

    Okay, I am a dunce! Win98 to XP on new disk???

    Thanks Andy, I had read that FAQ and I had installed clean. I had even set up the boot to Win98 or XP option, ... important since I have old software which I suspect XP will not run (since the Win2000 at work does not). However, XP creates a fresh Win98 install also, so I will have another...
  8. A

    Okay, I am a dunce! Win98 to XP on new disk???

    My confidence is completely shot! I have not been able to upgrade from my old Win98 on a 10 gig to XP on a new 60 gig. If I upgrade to the old disk I am stuck with it as my boot disk rather than a backup. If I upgrade to a clean system on the new disk I have no idea how many reinstall...
  9. A

    Abit Bx6 2.0 CPU Upgrade Options?

    You don't overclock??!?? Then what is that p3 450 riding at 527 for?? Just a flukey boot? ;) anvil
  10. A

    Abit Bx6 2.0 CPU Upgrade Options?

    I believe the latest bios is QR. It allows you to reach 153 fsb and multipliers up to 8.5 I believe, but I may be low on the multipliers. Fine board, I think. I run a 750e at 1000, Prime95 stable. It runs 138 stable also, if cool, but too much summer heat and it gives too much trouble. The...
  11. A

    abit bx6 rev2.0 + P3 700e slot 1 . . .how high can i go?

    The bx6 R2 equipped with the QR bios will allow you to reach 153 fsb, which is 1071 mhz. I don't believe there is a later bios than QR. You can also push vcore voltage a little higher than it initially allows in bios by some tricks that a search here or on Overclockers.com will explain. If...
  12. A

    need advice on ABIT BX6 rev2 OCing

    The 133fsb runs with 1/4 divider and yes, you should set the agp to 2/3. I don't know about the tnt, but I believe I've heard that the nvidia based cards oc well in general. I'd try it. If you can get Prime95 to run stable for a few hours, then you know the processor is working fine. If...
  13. A

    Intel OEM chips in Retail Boxes!!!!

    What I understood Wingznut Pez to have said, and I paraphrase here, is ... Retail is no better than OEM and OEM steppings might be sold by Intel as Retail from time to time. So if you, like I, spent extra for Retail, that is our mistake. It is simply coincidence that my Retail, an older cBO...
  14. A

    P3 1GHz overclocking adventures

    You're gonna hafta get that temp down! If nothing else, open the box and put a fan on it. Sounds like you have a good chip, but a p3 under load should not be that hot if you are trying to push to high speeds. anvil
  15. A

    For you watercooling overclockers

    Gee, I don't know! Come to think of it, what would happen if one of those tiny wires in your fan motor cable found its way to some component that it might be touching inside the computer? Now I'm REALLY worried! Actually, there is no direct electrical connection between the computer and the...
  16. A

    best slotket for overclocking on Abit BX6-2

    Dunno,... but I am presently running a p3 750 @ 1000-1035, 1.78v on a water cooled bx6 R2 using the MSI 6905 for what that's worth. anvil
  17. A

    Future of the processor market?

    Butch, Did your 433 last long enough? I'm sure any p3 will exhaust your interest in it. Question is whether the increase in performance is worth the added cost. All the 700+ p3's will give a dramatic improvement. At $210 you can even go for a p3 1gig chip which might even take you up to...
  18. A

    Is it possible to o/c a P3 850 E to 8.5 x 133 ? **some other questions**

    Powder, Just curious, is that Prime95 stable? Seems a lot of folks run systems that don't make it with Prime95, but do okay with most other software. I've become interested in what people mean by "stable". anvil
  19. A

    Can you reflash the bios for higher voltage on the Abit bx6 R2

    Very happy to report that this works! LutaWicasa on Overclockers.com advised that you need to reflash with the extension " /sn /cc" on the bx6 R2. You MUST set voltage to max in bios before doing this. It leaves all old voltage selections intact and adds new voltages up to 2.05. I...
  20. A

    Can you reflash the bios for higher voltage on the Abit bx6 R2

    Checked again Snowman. Try to find the thread "Abit BH6 1.85v???" in the Intel CPU forum. I also saw the same thing in other threads but with the extension reduced to just "/cc", which is the only one I have tried. I hoped to find someone with board specific experience...
  21. A

    Can you reflash the bios for higher voltage on the Abit bx6 R2

    Sure Snowman. I picked this up at the Intel Motherboard or Intel Processors Forum on overclockers.com. Do a search for reflash bios. Most posts referred to other motherboards, but there was an implication that it might work on several Abit boards.
  22. A

    Can you reflash the bios for higher voltage on the Abit bx6 R2

    I guess I about said it all above. A search here for "reflash bios" got nothing, but I had read on the Overclockers Forum where some Abit boards allowed the reflash of the bios to higher voltages using the switch /cc in the command line. I tried to reflash "bxr_qr.bin" with...
  23. A

    Krazy Kooling Question

    I have a water cooled abit bx6 R2 with a 750 OC'd to 968. My RT1 (chip diode) temp will run 47-49 with water cooler or the Intel heat sink. Meanwhile, with the sink mounted heat sensor, the RT2 temp is 42-45 with the Intel heat sink. On the Water cooled, it drops to 31-35. The RT1...
  24. A

    P3 > 700 in Abit bx6-R2 without new setup at every boot???

    Yes, you can avoid the setup after all. I found the answer over at Overclockers.com forum for Intel based motherboards, but thanks anyway. anvil
  25. A

    P3 > 700 in Abit bx6-R2 without new setup at every boot???

    No replies! Is everyone using too fast a processor in an abit board having to run setup each time they boot? anvil
  26. A

    P3 > 700 in Abit bx6-R2 without new setup at every boot???

    I know a number of folks here are running 700+ processors in their abit board. When ever I boot my bx6-R2, bios QR, with a P3-750, it sends me back to setup or allows me to run crippled at 500 (7.5 X 66mhz). Is there anyway to avoid having to do a complete setup everytime you boot?? anvil
  27. A

    Best Current P3 to OC to 900+ ????

    The bios (QR) in the abit board handles to 700, although you can push past the "check setup" message and run at speeds not in current bios. How about the 750? Too much of a long shot? anvil
  28. A

    Best Current P3 to OC to 900+ ????

    Compuwiz1 has noted that he has had difficulty getting recent P3 700's as high as 933, so is there another chip that would be better in currently available versions? I have an abit bx6 R2 with water cooling. anvil
  29. A

    How do I contact Compuwiz1 for cpu price?????

    Thanks Demon! I missed that box, completely. I think I fixed it. anvil
  30. A

    How do I contact Compuwiz1 for cpu price?????

    I think the title says it all, but I have already left a private message for several days with no answer. Is there another way?
  31. A

    JB Weld copper shim to processor???????

    Mike, You are absolutely right about the mounting problem. It is a problem I am still fighting, but I have been trying hard to put together a near silent box since I acquired a video projector. DVD or Serious Sam at 80 inches is a sight to behold! I am going after a quieter power supply...
  32. A

    JB Weld copper shim to processor???????

    WarCon, Thanks! I was not aware of Artic Silver's epoxy. You would think that would be better than JB Weld. Who has it? I had thought about silver too, but my ancient physics book states that silver conductivity is .97 versus copper at .92, which is not a lot of difference (aluminum comes...
  33. A

    JB Weld copper shim to processor???????

    Forgive me Mike. You have the commercial "shim" that is currently being marketed in mind and I did not mean that and never have seen one, but I intended the term as I have heard it used over the years in other applications. I apologize for the confusion. I simply meant a copper...
  34. A

    JB Weld copper shim to processor???????

    Why? My understanding is that several heat sinks such as some of the Alphas as well as some Step Thermodynamics cooling systems, have (or have had) a copper plate bonded to the aluminum or the processor because the copper conducts heat better and the bonding process between the copper shim...
  35. A

    JB Weld copper shim to processor???????

    I'm sure others have done similar things. In fact, I believe that this is also the same basic process that Step Thermodynamics used with their OC'd cpu's, but there may have been a more specialized "bonding" process used with the cooling plate. anvil
  36. A

    JB Weld copper shim to processor???????

    I read, in OverClockers.com, a suggestion that applying a thin coat of JB Weld (Heat stable epoxy) to attach a cooler to the processor worked well. What's your thought on doing same to a copper shim. Then the contact area to the cooler can be large, while the contact between the shim and the...
  37. A

    Abit bx6-2 no go with Celeron 633??????

    Sorry guys, ... just in from work. I have the processor back in at 66fsb and I don't have the number written down, so I will have to take 'er down to get that. But I wanted to reply first. I do recall that it is a Malay SL3VS with the FPO/batch# Q039????, I believe, but I could be wrong about...
  38. A

    Abit bx6-2 no go with Celeron 633??????

    Thanks! I tried 100 mhz, but it would not boot. If the bios is not stopping it, then could the temperature differences be the problem. I am water cooled. I have not tried another speed since I had to remove the processor and replace it with the old processor to get it to boot again. anvil
  39. A

    Abit bx6-2 no go with Celeron 633??????

    The latest bios (QR) does not recognize the 633. I have seen 633 OC'd at Overclockers.com run in bx6-2 boards. What is the secret? Is there another bios that accepts the 633? Also, when in setup, the rt1 temp shows 47-49, which seems high since the rt2 is nearer to 30. I am using an...
  40. A

    Any succesful 633->950 OCs out there? What are the chances?

    Reaper, You are using an abit bx6 r2 for your celery 633. So am I, but my bios (QR) does not recognize the 633. I don't know if that is a factor, but when I try to bypass the request to return to the bios setup after setting 100 mhz as the fsb, the thing will not boot and refuses to reboot...
COMPANY
RESOURCES
FOLLOW
Top Bottom
sale-70-410-exam    | Exam-200-125-pdf    | we-sale-70-410-exam    | hot-sale-70-410-exam    | Latest-exam-700-603-Dumps    | Dumps-98-363-exams-date    | Certs-200-125-date    | Dumps-300-075-exams-date    | hot-sale-book-C8010-726-book    | Hot-Sale-200-310-Exam    | Exam-Description-200-310-dumps?    | hot-sale-book-200-125-book    | Latest-Updated-300-209-Exam    | Dumps-210-260-exams-date    | Download-200-125-Exam-PDF    | Exam-Description-300-101-dumps    | Certs-300-101-date    | Hot-Sale-300-075-Exam    | Latest-exam-200-125-Dumps    | Exam-Description-200-125-dumps    | Latest-Updated-300-075-Exam    | hot-sale-book-210-260-book    | Dumps-200-901-exams-date    | Certs-200-901-date    | Latest-exam-1Z0-062-Dumps    | Hot-Sale-1Z0-062-Exam    | Certs-CSSLP-date    | 100%-Pass-70-383-Exams    | Latest-JN0-360-real-exam-questions    | 100%-Pass-4A0-100-Real-Exam-Questions    | Dumps-300-135-exams-date    | Passed-200-105-Tech-Exams    | Latest-Updated-200-310-Exam    | Download-300-070-Exam-PDF    | Hot-Sale-JN0-360-Exam    | 100%-Pass-JN0-360-Exams    | 100%-Pass-JN0-360-Real-Exam-Questions    | Dumps-JN0-360-exams-date    | Exam-Description-1Z0-876-dumps    | Latest-exam-1Z0-876-Dumps    | Dumps-HPE0-Y53-exams-date    | 2017-Latest-HPE0-Y53-Exam    | 100%-Pass-HPE0-Y53-Real-Exam-Questions    | Pass-4A0-100-Exam    | Latest-4A0-100-Questions    | Dumps-98-365-exams-date    | 2017-Latest-98-365-Exam    | 100%-Pass-VCS-254-Exams    | 2017-Latest-VCS-273-Exam    | Dumps-200-355-exams-date    | 2017-Latest-300-320-Exam    | Pass-300-101-Exam    | 100%-Pass-300-115-Exams    |
http://www.portvapes.co.uk/    | http://www.portvapes.co.uk/    |