Search results

  1. R

    Overclocking an E8400 on stock cooler

    Should be OK with the stock cooler - I am using the stock intel cooler (ex E6750) and I am running my E8400 at 9x400 - 3.6ghz. I did need to manually set the vcore to 1.25 for stability. Temps are 40 deg idle and 58 deg under load (OCCT etc) The temps normally dont go above 45 deg for...
  2. R

    8800GT running toooo hot!!!!

    exactly.. you want a colder case you need a dual slot cooler that blows the hot air out, rather then into the case. Not necessarily a lower temp for your card Yeah - good point, so are there any aftermarket coolers I can fit to my 8800GT that will allow the hot air to blow outside the PC...
  3. R

    Gigabyte P35 DS3P DDR voltages

    Thanks for the input - yes I thought the board would use the default voltage, but had no way of checking. EasyTune 5 does give the VDimm voltage in "Advanced Mode" - not sure how accurate it is but at least its a guide. At least the board boots OK with voltage default settings. At +0.3v...
  4. R

    8800GT running toooo hot!!!!

    As referred to earlier, these cards are expected to run hot, but thats no reason to allow them to. If the video card approaches 100 deg C + this heat is going to be transfered into the PC case, causing other components (CPU, RAM HDD) to run at higher temps. Putting extra fans on the case...
  5. R

    Gigabyte P35 DS3P DDR voltages

    I looks as tho the Gigabyte EasyTune app displays DDR voltages (VDIMM) - I will check it out when I get home later.
  6. R

    XfX 8800GT temperature and fan control

    Thanks mate - just what I was looking for. Next time I wil remember to use the search funtion on the forum :)
  7. R

    Gigabyte P35 DS3P DDR voltages

    I have set up a new system using a GA P35 DS3P with Corsair PC 6400 C4 ram which is supposed to run at 2.1 volts. Since the "standard" DDR2 volts is 1.8 - 1.9, does the motherboard automatically set the DDR volts to 2.1 with this RAM - or do I have to raise the volts in the bios (+0.2...
  8. R

    XfX 8800GT temperature and fan control

    Just picked up an XFX 8800GT and installed the drivers and utils of the disk that came in the box. After running the card for about 15 - 20 minutes, I decided to check the temperature by touching the plastic covering on the heatsink - it was almost too hot to keep my finger on it. I also...
  9. R

    Living with Cold Boot Problem

    Could you please describe the cold boot problem you are experiencing and what hardware (CPU, RAM, PSU etc) you have and any other relevant information that might help.
  10. R

    Gigabyte P35 Motherboard Thread

    Well in reply to my own post - I picked up an E6750 to replace my E4400 and am happy to say that the double post/boot issue is gone at last :) Would this be due to the new chip having a different "strap" than the old 800 FSB chip ? Anyway I am very happy with the replacement - currently...
  11. R

    Gigabyte P35 Motherboard Thread

    I was wondering if anyone using the new 1333fsb C2D's E6750/6850 still has the double post/boot issue when overclocking using the P35 motherboards. I currently have an E4400 with a P35 DS3 and the only way around the double post/boot issue I have found is to use either the 3.33 or 4 ram...
  12. R

    Gigabyte P35 Motherboard Thread

    Has anyone tried the F4 bios for the P35 DS3 yet ?? If so are there any improvements ?
  13. R

    Gigabyte P35 Motherboard Thread

    Hi Dulanic, Is the cold boot issue you are having the same one I referred to in an earlier post - computer starts then stops and then boots when overclocking. If so I would be interested in finding out if changing your RAM helps, especially as I was considering replacing my Corsair for OCZ...
  14. R

    Gigabyte P35 Motherboard Thread

    Thanks for the info Kougar - I did have some suspicions about the RAM - turns out that the Corsair Ram I have actually uses ProMos 667 Mhz chips that overclock to 800 Mhz, so they sell them as PC6400 chips. Mine work OK at 900 Mhz 5 5 5 18 at 2.1V. I hear that DDR2 RAM prices are going up...
  15. R

    Gigabyte P35 Motherboard Thread

    I got my P35 DS3 last week, along with an E4400 and 2 gigs of Corsair DDR2-800 RAM. So far the setup seems very stable and I have overclocked the E4400 up to 3150 @ 1.39 volts. The only issue I have found with my setup is that when I started overclocking I found that when the computer was...
  16. R

    Palit 6800GS 512MB?

    Hi Crono - not sure if you made your video card purchase yet, if you have an AGP system, then I think the 6800GS is a good upgrade. I have just puchased an Xpertvision 6800GS 256 GDR3 - AGP, the card is the 6800GS PCie version - (NV41) instead of the native AGP (NV40). This means that it...
  17. R

    6800GS AGP

    Hi I have just purchased an Xpertvision 6800GS - 256MB and have had a lot of stability problems since upgrading from my old ATI9600. The problem appears to occur when playing games where 3d mode is used (Oblivion, BF2, CS tc) and 3dmark2001 crashes before completion. My system specs are Abit...
  18. R

    Abit AV8 Bios

    Thanks - vailr - I got the info I needed from the Abit site, it looks like I will stay with what works for now.
  19. R

    Abit AV8 Bios

    I have just updated to an Abit AV8 Motherboard and Venice 3200+, so far it performs very well. I have conservatively overclocked the chip with a FSB of 250x10 without raising the Vcore and still using the stock AMD cooler. I will probably push it a bit further when I get a new cooler. I...
  20. R

    Power Supply issues with 9NDA+ and Venice

    Thanks for the input - I kind of thought that was the problem, it seems strange that it just would not start. I can understand having stability problems after starting up - especially when overclocking. I will pick up an new PSU tomorrow and try again. It seems people are getting mixed...
  21. R

    Power Supply issues with 9NDA+ and Venice

    I am just setting up my new 9NDA3+ and 3200 Venice, but my first efforts to get the system to post were met with a small flick of the fans and FF code on the LED. I was starting with a minimal setup - Board, RAM, CPU Video card etc. I decided to try something different so I held down the...
  22. R

    Why are 3200+ XP's so hard to find?

    Hi I have the same board and ram as your system, and are using a 2500+ barton at 200 X 11 (3200+ speed). If your cpu has unlocked multpliers, why not lower it to 11 and set FSB to 200 i.e. 3200+ , should be easy and stable, even with stock cooler.
  23. R

    Cat 3.10 Driver Download

    Thanks for the replies folks - firstly Mem, I do have a copy of the Driver Cleaner you referred to, which I will most certainly use - especially after some of the problems I have had in the past with Nvidia drivers. I sure hope the Cat's update easier. To answer your comment Lonyo, I am fully...
  24. R

    Cat 3.10 Driver Download

    Thanks for the quick answer Mem, it will save me an hour or so of downloading time, and yes I will take your advice and remove the old control panel & driver first. Thanks again
  25. R

    Cat 3.10 Driver Download

    I heard that ATI had new Catalyst drivers out, so I went to the download site at ATI and noticed the whole package is over 22MB - a bit steep for my 56k dial-up connection. The question I have is do I need to download the whole 22MB package or can I just download the "display driver" portion...
  26. R

    Which Hard Drive

    Thanks for the quick answers on a new HDD, I managed to find that article on the WD drive issues when used on 8RDA mobo's, it was posted under the issues section for the 8RDA's on the "motherboardfaqs" website - as follows: Hard drive not detected - (Western Digital especially) The first thing...
  27. R

    Which Hard Drive

    I need a new/bigger hard drive for my Athlon 2500/8RDA+ system, I was thinking of getting an 80 gig Maxtor with the ATA133 interface - anyone have any thoughts good or bad on these HDD's. Or are there other brands that also have the ATA133 interface that can be recommended. I seem to remember...
  28. R

    Epox 8rda+ Bios help

    Thanks for the help, I flashed the 3609 bios successfully and all works OK, overall the system appears to be more stable. Scandisk fixed my Win XP issues - luckily. At this stage I am leaving my 2500+ O/C to 2800+ (166@12.5). I will intend to purchase some decent ram soon, so then I can try to...
  29. R

    Epox 8rda+ Bios help

    Thanks for the quick answer Megatomic, I will try the 3609 bios to see if that helps, I am not sure about the problems with the 13X multiplier. I also have PC2700 ram which does not O/C very well, so I was hoping to use only the mutipliers, but it looks as though 12.5X is about the limit. Regards
  30. R

    Epox 8rda+ Bios help

    I have just upgraded my CPU to a 2500+ on my 8rda+ mobo. The upgrade worked fine at first, but then I decided to have a try at some overclocking. It went OK up to 166@12.5 - 1.8 volts, but when I tried 166@13 it would not post. No problem I thought I will just reset the cmos and all should be...
  31. R

    MSI Slotket Jumper Settings

    Would anyone have the Jumper Setting details for an MS6905 Master V 2.0 slotket. I have aquired an old P600 system which I would like to upgrade, however it came with no manuals or info, so I am a bit lost. There does not seem to be any silkscreen info on the PCB so I assume there must have...
  32. R

    Will amd XP 1600 work on Asus A7v133 and Gigabyte GA-7zx

    I have just got my ASUS A7V133 C running with and XP1800+, but because it was an older revision (1.0) I had to set the CPU via the jumpers instead of the bios. As SoulKeeper suggested to me, take a look at this website at http://a7vtroubleshooting.com it should help. Good Luck
  33. R

    XP compatiblity with Asus A7V133-C

    Sorry about the late reply, I have have been off the Net for a while. The only benchmark I have tried is 3DMark2001 Pro, went from 5250 to 6556 3D marks using a GeForce 3 TI 200, which is a reasonable gain in my opinion. I have noticed that the CPU runs a bit hotter now, up from 48C loaded to...
  34. R

    XP compatiblity with Asus A7V133-C

    Success - switched to jumper mode and set up dipswitches etc - booted up with no problems - thanks for the info Soulkeeper.
  35. R

    XP compatiblity with Asus A7V133-C

    Thanks Soulkeeper, I have just had a look at the website that you suggested and it looks very useful. From what I can tell it looks like the particular revision of my board requires that I set the FSB by using the DIP switches instead of by the bios and that is supposed to work. I will give it a...
  36. R

    XP compatiblity with Asus A7V133-C

    Has anyone had any success with using an Athlon XP on an older Asus A7V133-C motherboard? I have tried to upgrade my old 1Gig T/bird with an XP1800+ but I have not been able to get the computer to POST with the new CPU. I have updated (and checked) the bios to the latest version (1009) as...
  37. R

    K7S5A EXPERIENCE

    Hi Dr Zepp, I have just had a similar experience with a K7S5A. There was a number of small problems following the installation, but the main problem was accessing the internet via an internal modem (Motorola) - after a short time the screen would go black with a blinking cursor or it would shut...
COMPANY
RESOURCES
FOLLOW
Top Bottom
sale-70-410-exam    | Exam-200-125-pdf    | we-sale-70-410-exam    | hot-sale-70-410-exam    | Latest-exam-700-603-Dumps    | Dumps-98-363-exams-date    | Certs-200-125-date    | Dumps-300-075-exams-date    | hot-sale-book-C8010-726-book    | Hot-Sale-200-310-Exam    | Exam-Description-200-310-dumps?    | hot-sale-book-200-125-book    | Latest-Updated-300-209-Exam    | Dumps-210-260-exams-date    | Download-200-125-Exam-PDF    | Exam-Description-300-101-dumps    | Certs-300-101-date    | Hot-Sale-300-075-Exam    | Latest-exam-200-125-Dumps    | Exam-Description-200-125-dumps    | Latest-Updated-300-075-Exam    | hot-sale-book-210-260-book    | Dumps-200-901-exams-date    | Certs-200-901-date    | Latest-exam-1Z0-062-Dumps    | Hot-Sale-1Z0-062-Exam    | Certs-CSSLP-date    | 100%-Pass-70-383-Exams    | Latest-JN0-360-real-exam-questions    | 100%-Pass-4A0-100-Real-Exam-Questions    | Dumps-300-135-exams-date    | Passed-200-105-Tech-Exams    | Latest-Updated-200-310-Exam    | Download-300-070-Exam-PDF    | Hot-Sale-JN0-360-Exam    | 100%-Pass-JN0-360-Exams    | 100%-Pass-JN0-360-Real-Exam-Questions    | Dumps-JN0-360-exams-date    | Exam-Description-1Z0-876-dumps    | Latest-exam-1Z0-876-Dumps    | Dumps-HPE0-Y53-exams-date    | 2017-Latest-HPE0-Y53-Exam    | 100%-Pass-HPE0-Y53-Real-Exam-Questions    | Pass-4A0-100-Exam    | Latest-4A0-100-Questions    | Dumps-98-365-exams-date    | 2017-Latest-98-365-Exam    | 100%-Pass-VCS-254-Exams    | 2017-Latest-VCS-273-Exam    | Dumps-200-355-exams-date    | 2017-Latest-300-320-Exam    | Pass-300-101-Exam    | 100%-Pass-300-115-Exams    |
http://www.portvapes.co.uk/    | http://www.portvapes.co.uk/    |