http://www.amdpower.com/sections.php4?op=viewarticle&artid=66
one other question on where to take readings (see above)
above it shows that you take it from the dot to left side of l1 then right side of l1
if so what should be the readings?
or is this wrong and do you just take it across the l1...
yea... and i believe i have an agoga core but i never checked b4 i sploshed on the as3 how can i make sure b4 i unlock i have an xp that just needs L1 bridges connected and one where no cutting is necessary (its green if that helps )
and also with volt/multi meter someone told me to set it to...
whats worng with o/c ?
ive tried upping fsb up from 133 but it wont hold when i benchmark
when i try to run at 166 fsb (so 1/5 divider kicks in) windows gets fatal errors and shuts down (blue screen in xp)
i have a soyo dragon kt333 lite
xp 1900 (agoga)
corsair xms pc-3000
allied 350 watt psu
80...
just recieved my replacement for defective parts and put together another xp system
have yet to unlock cpu
but im wondering about voltages for just FSB o/cing
i have xp 1900 soyo kt333 lite
and corsair xms pc 3000 256mb ddr
right now its running pretty cool i have 3 case fans, 2 in back 1 on...
ok i finally sent off rma of cpu ram mobo psu and got all new parts from newegg :-)
now installing xp fat32 wont allow partitions over 32gb, microsoft says go with ntfs unless ur gonna use older os (which im not) and that if u have older progs/software that wont run with it(<--???) so what...
how do the pins go in? a friend of mine told me that the text should be facing outside and the metal part should be facing on the inside (maybe i misheard?) he did it on mine and it booted up but now, since i had to do an overhaul, i had to unplug what he did... i did what he said and have...
yes there are enough standoffs...
i have tried two video cards on 2 pcs with two monitors each (and i have switched the monitor power cable)
i had one pc working fine since april with the good agp 4200 video card when i put it back in there was no video...
i did get into the bios a few times...
yes warconn that may be the case but i am getting no video on both pcs with same video card (and one pc i had the video card running just fine for a few months) also i have tried an older pci video card and i still get no video
great ... well i put the geforce 4 back into my other xp system (was working fine with that card) and now no Video from that card either... wtf pls help!
i have yet to send it back and get RMA in the mean time id like some oppinions of what to get basic mobo with o/cing with onboard sound, onboard lan is nice too... other then that just one that has voltage changes for agp ram and cpu and can o/c :-) i may buy a alpha cooler later but not now...
yes i know how ide cables work... after much trial my cpu is broken i believe and im going to RMA cpu and probably mobo and maybe PSU sorry no $$$ to give out cus its just broken ;-(
i ordered from newegg (minus vid card cdrw hard drive and monitor)
soyo dragon 333 lite
geforce 4 ti 4200
corsair xms pc 3000 256 mb ddr
chieftec silver dragon w/ window
liteon 52x cd rom
cendyne (liteon i believe) 40x16x48 cdrw
samsung floppy
maxtor 40 gb hard drive 5400 rpm
dr thermal...
ok well i took out cdrom power cables again and now it doesnt even show any thing on monitor.... im trying to build this for someone and im in a hurry so id be glad to send 20$ via mail if you can offer me a solution that works
thanks!
ok well i tried the regular ide cable that came with cdrw put black one on cdrw which had master has master setting and gray one on cdrom which is slave... and i put that on board ... so then i boot up same thing so i decide well ill go back a step and see if it still works.
so i remove the...
im building from scratch and have yet to install an os..... the video has been on and off whole time i have been building with two monitors so im wondering what could it be? after a while of playing around i can get it to work but i have no idea what i am doing... i did use a hard drive ide...
soyo dragon 333 lite
geforce 4 ti 4200
corsair xms pc 3000 256 mb ddr
chieftec silver dragon w/ window
liteon 52x cd rom
cendyne (liteon i believe) 40x16x48 cdrw
samsung floppy
maxtor 40 gb hard drive 5400 rpm
dr thermal extreeme (modded vl77) with tornado 84cfm fan
athlon xp 1900
generic 17...
i have pc 3000 of same corsair xms
is it ok to put the setting for ram at 166 ? and what are the fastest memorie timings, cas 2 6 t?? somethin somethin
i have no clue about memorie timings !
ok i got one off crazypc where i got my hs/f now someone said to place the dial on the horse shoe looking thing and put it at 200? now where do i place it on gap/bridge or the l1? and what should the readings be for all of those...
also i already tried it once but failed its a green xp so im...
ok first off system specs
xp 1900
visiontek ti 4200
chieftec case with 3 case fans + window
soyo dragon 333 lite
3000 ddr xms corsair xtreme
dr thermal extreme (vl77 with a tornado 84 cfm 80 mm fan)
_______________________
i have cdroms cdrw and hd i havent installed yet i was just trying to...
which two places do i measure on my xp to see if it is unlocked and what should the reading be... i orderd multi meter and unlocking kit (high speed pc) and instructions are confusing... also once i am done unlocking is it ok to keep a piece of tape on there so it doesnt get messed up or will...
which two places do i measure on my xp to see if it is unlocked and what should the reading be... i orderd multi meter and unlocking kit (high speed pc) and instructions are confusing... also once i am done unlocking is it ok to keep a piece of tape on there so it doesnt get messed up or will...
i ordered parts for my new pc im building and unlocking kit (high speed pc one) came in first so i figured id unlock my old xp 1800 now just a quick question you just undo lever and take off hs/f correct? and is it ok to keep same as3 on there or scrape off and put new layer?
there pretty slow now if you see the actual cdrw speeds there like 12 write and for a dvd thatll be a long time, cd burners used to be that much now u can open an ad for any store best buy circuit city office depot/max comp usa and find a fast burner for 30 bux or so id wait and save ur money IMO
this happened to me when building my computer everything turns on for a sec then turns off i didnt have my vid card on rite and it was sagging my mobo down... well actually my mobos bent in the middle a bitt oh well it runs ;-) put all standoffs and make sure ur vid card and any pci cards are rite
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.