Search results

O
*** Official ABIT IC7/G (875P) Thread ***

Oldfart, I used the same zalman NB Heatsink that you have, and I used the thermal adhesive, since there are no holes, only clips, for the other methood. I know it's a permanent solution now, and I'm willing to live with that. I was also using speedfan before to lower the RPM's, but now I...
- O1dieburg
- Post #242
- May 14, 2003
- Forum: Motherboards
O
*** Official ABIT IC7/G (875P) Thread ***

Jdog, I had the same problem with the USB/Firewire headers. I have one of those USB 2.0 internal 6-in-1 readers, and if it was connected during boot it wouldn't get past post. After upgrading the bios, problem went away. I also had 2 Seagate 120g SATA drives in RAID 0 and didn't...
- O1dieburg
- Post #233
- May 13, 2003
- Forum: Motherboards
O
*** Official ABIT IC7/G (875P) Thread ***

Anyone know where the temp readings are comming from on this board (with the exception of the CPU one of course). I'm assuming somewhere around the northbridge and maybe down near the PCI slots. Can't seem to find it in the docs, and I'd rather not tear this thing apart again looking. Thanks!
- O1dieburg
- Post #181
- May 8, 2003
- Forum: Motherboards
O
*** Official ABIT IC7/G (875P) Thread ***

I meant the A, sorry about that. I knew there was a revision, and assumed it was "B" before checking... you know what they say, never AssUMe...
- O1dieburg
- Post #116
- May 2, 2003
- Forum: Motherboards
O
*** Official ABIT IC7/G (875P) Thread ***

Hello, I recently took the plunge and ordered this MB as well. It was to replace an ASUS P4B266-C that came with my first P4, a 1.8a that has been running at 18x133 default voltage for about a year now, with 2x256mb crucial ddr at pc2100. I also upgraded my disks to 2 120gb Seagate SATA...
- O1dieburg
- Post #114
- May 2, 2003
- Forum: Motherboards
O
9v DC inside the case?

I think I'll try the 7809 route as the device uses .1A. I would rather not feed off the 3.3v connector, just for the potential risk. Thanks!
- O1dieburg
- Post #4
- Apr 25, 2003
- Forum: Ask a Technical Professional
O
9v DC inside the case?

Hello, Since my DC circuit building skills have waned since college, I was wondering if someone knows of what I would need to do to get a 9vdc current off a standard PC power supply. I know I can get 12v and 5v, obviously, so I figure I would need to step down the 12v supply somehow. The...
- O1dieburg
- Thread
- Apr 25, 2003
- Replies: 5
- Forum: Ask a Technical Professional
O
MSI 865PE NEO2 already available???

Hey PClark99... Does it have the ICH5 or ICH5R southbridge on it? In other words, does it do SATA RAID? Thanks
- O1dieburg
- Post #75
- Apr 23, 2003
- Forum: Motherboards
O
MSI 865PE NEO2 already available???

Does this board support SATA RAID in the southbridge? I was going to get the Canterwood but if the support is there I'll save some $$. Thanks
- O1dieburg
- Post #69
- Apr 22, 2003
- Forum: Motherboards
O
New motherboard that supports hard power on switch...

Here is the situation: I retrofitted an old arcade cabinet (Space Dual) with A PC. I'm currently using an old Gigabyte AT Pentium II motherboard that supports only up to 400mhz (Dip Switches). I am looking to upgrade the motherboard in the cabinet to get something a bit faster. The...
- O1dieburg
- Thread
- May 24, 2002
- Replies: 1
- Forum: Motherboards

RESOURCES

Top Bottom