So after once trying watercooling I decided to do a 2nd build on same PC.
I was disappointed with the placement of reservoir and the fact that the HAF 932 is so tiny and hard to work with unmodified.
Also I wanted to eliminate leak damage, so now if reservoir, rad, pump leak no PC component gets water over it.
I decided to drill out DVD and Harddrives as I only use SSD :
I don't have washers for the M3 screws so I use Cable ties to install front radiator:
Started put in some tubes:
Motherboard installed:
Tubing complete until GPU blocks get:
I make a BIG MISTAKE on reservoir tubing, now It is difficult to fill, so I need take a Coca Cola plastic bottle, drill hole in Coke cap, put a straw in it and fill reservoir
Once I make my 3rd and final build (gpu blocks + external rad) I put LONG tubes to Reservoir.
I'm running out of tubes and will have to wait until I make my GPU block order to get more tubing.
I spent like 2-4 hours on trying to make the tubing between Pump and Rad to not kink, all my tubes were kinking finally using 2x 45degree fitting on Rad it is almost no kink!
I'm having 2x 7950 and 1x 7970 all in this computer, so I also going to Buy Phobya Super Nova 1080 so that no noise is coming from PC
Buy list for 3rd and hopefuly final build:
Phobya 1080 + 4x 180mm silent fans
M3 Washers
M3 Screwdriver <--- Where the hell I can get this, I have 1 million bits none fit the M3 and Res screw so I have to use that tiny align key that came From EK Res.
2x EK-7950 GPU block
1x EK 7970 GPU Block
2-4 meter Tubing
Phobya Sandwich Foam Pad for D5 pump
2x Silver Coil
Maybe I also get Tube cutter but the Scissors I have cut good aswell
Maybe I get HAF932 door with big window so see inside case
I was disappointed with the placement of reservoir and the fact that the HAF 932 is so tiny and hard to work with unmodified.
Also I wanted to eliminate leak damage, so now if reservoir, rad, pump leak no PC component gets water over it.
I decided to drill out DVD and Harddrives as I only use SSD :
I don't have washers for the M3 screws so I use Cable ties to install front radiator:
Started put in some tubes:
Motherboard installed:
Tubing complete until GPU blocks get:
I make a BIG MISTAKE on reservoir tubing, now It is difficult to fill, so I need take a Coca Cola plastic bottle, drill hole in Coke cap, put a straw in it and fill reservoir
Once I make my 3rd and final build (gpu blocks + external rad) I put LONG tubes to Reservoir.
I'm running out of tubes and will have to wait until I make my GPU block order to get more tubing.
I spent like 2-4 hours on trying to make the tubing between Pump and Rad to not kink, all my tubes were kinking finally using 2x 45degree fitting on Rad it is almost no kink!
I'm having 2x 7950 and 1x 7970 all in this computer, so I also going to Buy Phobya Super Nova 1080 so that no noise is coming from PC
Buy list for 3rd and hopefuly final build:
Phobya 1080 + 4x 180mm silent fans
M3 Washers
M3 Screwdriver <--- Where the hell I can get this, I have 1 million bits none fit the M3 and Res screw so I have to use that tiny align key that came From EK Res.
2x EK-7950 GPU block
1x EK 7970 GPU Block
2-4 meter Tubing
Phobya Sandwich Foam Pad for D5 pump
2x Silver Coil
Maybe I also get Tube cutter but the Scissors I have cut good aswell
Maybe I get HAF932 door with big window so see inside case