Abit IP35-E Cooling

[Tweakin]

Just picked up this board and want to see who is using what. I'm leaning towards a TRUE.

Whoops, wrong Forum...MOD, can you move me please...

 

[nerp]

Tuniq Tower 120 and if fits like a glove.

 

[superstition]

Will the Xigmatek 1283 fit?

 

[MadScientist]

An el cheapo Coolermaster Hyper TX2 + Thermalright Bolt-thru kit with an Antec 900 case, fits perfectly on this MB.

 

[Tweakin]

Originally posted by: MadScientist
An el cheapo Coolermaster Hyper TX2 + Thermalright Bolt-thru kit with an Antec 900 case, fits perfectly on this MB.

I thought the Thermalright Bolt-thru kit was for 939 series chips...is the pattern identical to 775?

 

[MadScientist]

Thermalright Bolt-thru kit SVC also carries it.

 

[richwenzel]

zerotherm btf92

fit a bit tight.

 

[imported_Scoop]

Originally posted by: richwenzel
zerotherm btf92

fit a bit tight.

Are the fins a little higher on the BTF-92 OC model than the BTF-90? I had to cut few of the lowest fins to make it fit blowing towards the rear exhaust. Or have you oriented it to blow towards the top of the case?

 

[richwenzel]

didnt have to remove anything, but if kept it facedown fan nicked something when it spun...so i had to point it upwards...

thing is the cooler is not that big compared to like TT

 

[Tweakin]

Originally posted by: MadScientist
Thermalright Bolt-thru kit SVC also carries it.

Thanks...ordered one just in case. I'm leaning toward a Scythe Ninja...the position of this in an Antec 900 is really nice.

 

[watek]

Originally posted by: MadScientist
An el cheapo Coolermaster Hyper TX2 + Thermalright Bolt-thru kit with an Antec 900 case, fits perfectly on this MB.

Using the same setup with backplate!

 

[toadeater]

Originally posted by: superstition
Will the Xigmatek 1283 fit?

Yes.

 

[Tweakin]

I ended up going with the scythe ninja...thanks for all the inputs.

 

[METALWORK]

Hey. Doing a new build and I'm in on this board with a 900 Antec case. What is your plan for cooling the NB with the ninja? I'm deciding between the Coolermaster Hyper tx2 which looks like it will help out in that regard and the ninja. Also will the mount that comes with the ninja be sufficient?

 

[Tweakin]

Originally posted by: METALWORK
Hey. Doing a new build and I'm in on this board with a 900 Antec case. What is your plan for cooling the NB with the ninja? I'm deciding between the Coolermaster Hyper tx2 which looks like it will help out in that regard and the ninja. Also will the mount that comes with the ninja be sufficient?

I purchased a spring screw kit for the ninja...I'm just not a fan of the plastic push-pins. I have pre-mounted the mb in the case and the ninja is almost in perfect position for the two exhaust fans. Most likely I will mount my trusty 120 Panaflow above the memory and blow towards the rear fan.

As for the NB, I'm currently burning in with Orthos and temps (touched the sink several times) seem to be low...so right now I just don't see the need for any other cooling.

 

[PingSpike]

Originally posted by: Scoop

Originally posted by: richwenzel
zerotherm btf92

fit a bit tight.

Are the fins a little higher on the BTF-92 OC model than the BTF-90? I had to cut few of the lowest fins to make it fit blowing towards the rear exhaust. Or have you oriented it to blow towards the top of the case?

I have either the 92 or the 90...can't remember which one. It fit with no issues on my IP35 Pro. Its tight on one side, but no issues.

 

[Dorkenstein]

Does the scythe infinity use the push pins also?

 

[Reckoner]

I'm using a Big Typhoon, it's great.

 

[Tweakin]

Originally posted by: Dorkenstein
Does the scythe infinity use the push pins also?

Yes it dows, but I removed them and went with a spring loaded screw design. Very nice.