EasyTune5 with gigabyte motherboard

[paulmichaelkemp]

ok i'll try these setting now and see if my comp reboots,lol, brb

 

[mrfatboy]

I guess I'm getting a little confused what you want. If you are fine with the 3.4OC and it's orthos stable then you are good to go.

What was your ram set at when you had 3.4OC stable?

It's rated at 5-5-5-15 2.2v.

If you want see if you can tighten the timings try 4-4-4-12 @ 2.2v.

Test if orthos stable. If so, try to lower memory volts by .1v. Test again. Repeat until not orthos stable then go back to last stable setting.

 

[paulmichaelkemp]

thats another thing, my ddr2/3 voltage control goes up in 5's? +0.05 - +0.10 - +0.15 what will i need to set the voltage at?


my ram timing is 5 - 7- 7 - 24 default

 

[mrfatboy]

Originally posted by: paulmichaelkemp
thats another thing, my ddr2/3 voltage control goes up in 5's? +0.05 - +0.10 - +0.15 what will i need to set the voltage at?


my ram timing is 5 - 7- 7 - 24 default

You are killing me just kidding.

Copy the settings i just gave you a couple posts back. 5-5-5-15 @ 2.2v (+.4v setting)

 

[paulmichaelkemp]

ok, lol but 2.2v is my default setting? do you know what i mean about ddr2/ddr3 overvoltage control going up in 5's?

 

[mrfatboy]

your ram needs 2.2v. Your board is default 1.8v. You need .4v to make 2.2v (1.8v +.4v = 2.2v). If it goes up by .05v at a time, that's fine. just set it to .4v

 

[paulmichaelkemp]

ok at 3.6 at 1.46v , ram is set at 900 at 5-5-5-15 +.4 ( 2.15) these setting i'm view by the easytuner. and i set the system voltage to auto. cos it was flashing red sayin it wasnt optimized. is that that then? shall i run orthos tonight see if it's stable?


my core temps with coretemps are 36 idle.

 

[mrfatboy]

Originally posted by: paulmichaelkemp
ok at 3.6 at 1.46v , ram is set at 900 at 5-5-5-15 +.4 ( 2.15) these setting i'm view by the easytuner. and i set the system voltage to auto. cos it was flashing red sayin it wasnt optimized. is that that then? shall i run orthos tonight see if it's stable?

Set system voltage to manual. Don't worry about the red flashing warning.

Don't use Easytuner. Throw it away.


Use Speedfan 4.33 and Coretemp 0.95.4. What does those voltages say?

 

[paulmichaelkemp]

speedfan temp1 35
temp2 29

cortemp both 36

 

[mrfatboy]

how about the voltages?

 

[paulmichaelkemp]

i just changed the system voltages to manual and also did the timing to 5-5-5-12 my voltages are on speedfan.... Vcore 1.42, Vcore2 2.22, +3.3v 3.33. +5 4.89, +12 1.86

-12v -16.64v, -5v -8.58, +5v 5.11, vbat 3.10v

 

[paulmichaelkemp]

coretemp, VID - 1.3500v

 

[mrfatboy]

ok, run orthos. Let's see if your 3.6 OC is stable. good luck

 

[paulmichaelkemp]

how long shall i run it for, can i just mess on the comp for another hour then leave it on overnight and tomorrow for about 15hr?

 

[mrfatboy]

I would run it for at least 12 hours. Go ahead and do little stuff like web browsing while it's running. The more stress the better If it crashes let us know then we can do more adjustments. good luck.

 

[paulmichaelkemp]

i'll do it now and leave it on until i get back from work tomorrow. thanks for the help. i know it must be fustrating helping a noob, but least your helping people to learn.

i'll let you know if it passes or fails. if it fails then we'll have to try something else

thanx again. and check here tomorrow

regards,
paul

 

[mrfatboy]

Also remember to watch those core temps. Let us know how hot it gets.


and take this time to READ THAT THREAD!!!!!!!!!!

 

[paulmichaelkemp]

temps are inbetween 60-64 is that ok?

 

[mrfatboy]

you are fine.

 

[paulmichaelkemp]

temp2 is at 56, i dont like it when they show a flame,lol.

 

[paulmichaelkemp]

temp2 is at 56, i dont like it when they show a flame,lol.

temp2 is the cpu?

 

[mrfatboy]

i always forget. You need to give all the speedfan temps and I can figure it out from there.

 

[dflynchimp]

lol, I'm gone for 6 hours and it looks like you've got lots of help since then...still want memset?

On a side note, RAM clockspeed won't drastically alter your real world performance. The difference between 4-4-4-15 800MHz and 5-5-5-20 1000MHz probably doesn't exceed ~5% on most applications.

 

[paulmichaelkemp]

sorry, just a quick message before i goto work ( i will be late) arthos failed after 2 hrs, 15mins & 32 secs. Fatal error: resulting sum was - 7.6937350100883866e+016, expected : 7438670536150273. Hardware failure detected, consult stress txt file.

1 error, 0 warnings.

so.... i guess we have to make some changed if i've not done any damage. Or is this bad? lol.

anyway i'll be back from work in 9 hours so, hope i'll have some feed back by then.


cheers all.

regards,
paul.

 

[mrfatboy]

I would now up the voltage to the CPU one notch and retest. That should be 1.4625. Your board is fine. It's just part of the testing process.