I just bought a combo off a guy at Hard OCP forums that was supposed to do 1000MHz.. This was a pretested setup from OCZ..
I am unable to get it to 1000, well I actually did get it there for a few minutes... I'll explain in a sec..
here's my setup:
KT7raid
duron 700
128MB PC133 EMS SDRAM (cas2)
GF2 GTS (reference board)
Live value
3c905
3c509b
win98 SE
7237 case w/all panaflo L1As, 300 watt
26ºc case / 33ºc cpu @900MHz
I did most of my testing with just the vid card in.. It was setup out of the box, but wouldn't make it to desktop (BSOD),. So I loaded the setup defaults and tried upping in 50 MHz incrememts and and ran a few tests each time... I made it up to 950 but a Q2 timedemo locked it hard in about 1/2 second
So I'm running pretty stable at 900 now. Everything is tweaked and running well Q2 Q3A Prime95 (bout an hour or two) 3DMark2000, no lockups or crashes...
He had this same combo running at 1000MHz with no problems. Only major difference is he was using a Stealth III s540 32MB PCI, and I have the GTS AGP..
I've tried setting RAM to cas 3 (swapped with a NEC stick for a bit too) and tried a couple differnt multiplier / bus speeds, and I just can't get it to load..
I did get it to load with a Asus V6800 DDR Pure... after about 9-10 tries with BSODs and registry fixes it finally loaded, and I was able to re-boot (and shut down restart) about 3-4 times. I thought maybe we had found the problem, so I tried a Q2 timedmo... no go, locked solid, and wasn't able to get it to the desktop again after another 8-10 tries.
Temps were looking good via HWM while in windows 21-32ºc (not sure how accurate the HWM is)
Most times while I have been "trying" it has read around 44ºc in the bios...
I broke down and tried an old ISA vid cards for sh1ts and giggles, but it didn't work, then remembered my bros. PC that was over here for a tune up, so I tried his V3 2000 with no luck...
Errors I'm seeing:
BSOD - fatal exception
windows protection error
Registry errors and restores
Most of the articles I've read (newbie to AMDs ) on OCing have included GTS grahics cards..
And it realy seems odd to me that this would be the problem as I'm not running the PCI out of speck.. correct ?? I would think that the prerifs. would have less of an influence on a OC with Multiplier.
Any ideas on what else I might try? Or opinions on what's holding me back?
Thanks!
EDIT:
Just thought I'd mention:
The board was setup out of the box at 10x100 1.825v
I tried that and 1.85v
900 is running at 1.725v
oops sorry bout the color.. just changed it
I am unable to get it to 1000, well I actually did get it there for a few minutes... I'll explain in a sec..
here's my setup:
KT7raid
duron 700
128MB PC133 EMS SDRAM (cas2)
GF2 GTS (reference board)
Live value
3c905
3c509b
win98 SE
7237 case w/all panaflo L1As, 300 watt
26ºc case / 33ºc cpu @900MHz
I did most of my testing with just the vid card in.. It was setup out of the box, but wouldn't make it to desktop (BSOD),. So I loaded the setup defaults and tried upping in 50 MHz incrememts and and ran a few tests each time... I made it up to 950 but a Q2 timedemo locked it hard in about 1/2 second
So I'm running pretty stable at 900 now. Everything is tweaked and running well Q2 Q3A Prime95 (bout an hour or two) 3DMark2000, no lockups or crashes...
He had this same combo running at 1000MHz with no problems. Only major difference is he was using a Stealth III s540 32MB PCI, and I have the GTS AGP..
I've tried setting RAM to cas 3 (swapped with a NEC stick for a bit too) and tried a couple differnt multiplier / bus speeds, and I just can't get it to load..
I did get it to load with a Asus V6800 DDR Pure... after about 9-10 tries with BSODs and registry fixes it finally loaded, and I was able to re-boot (and shut down restart) about 3-4 times. I thought maybe we had found the problem, so I tried a Q2 timedmo... no go, locked solid, and wasn't able to get it to the desktop again after another 8-10 tries.
Temps were looking good via HWM while in windows 21-32ºc (not sure how accurate the HWM is)
Most times while I have been "trying" it has read around 44ºc in the bios...
I broke down and tried an old ISA vid cards for sh1ts and giggles, but it didn't work, then remembered my bros. PC that was over here for a tune up, so I tried his V3 2000 with no luck...
Errors I'm seeing:
BSOD - fatal exception
windows protection error
Registry errors and restores
Most of the articles I've read (newbie to AMDs ) on OCing have included GTS grahics cards..
And it realy seems odd to me that this would be the problem as I'm not running the PCI out of speck.. correct ?? I would think that the prerifs. would have less of an influence on a OC with Multiplier.
Any ideas on what else I might try? Or opinions on what's holding me back?
Thanks!
EDIT:
Just thought I'd mention:
The board was setup out of the box at 10x100 1.825v
I tried that and 1.85v
900 is running at 1.725v
oops sorry bout the color.. just changed it