**Official AMD T-BRED B O/C RESULTS 1700+/2100+**

[fhetw]

great o/c mrspec did you buy from excaliber? what board are you using
looks like 0308/0309 seem to be doing the best.

 

[Mrspec3]

Originally posted by: fhetw
great o/c mrspec did you buy from excaliber? what board are you using
looks like 0308/0309 seem to be doing the best.

Got it from a local computer shop here in Toronto. They board I was using was an Epox 8k5a2+ which I have now replaced with an Abit NF7-S because the epox was limiting the overclock I could get with this CPU

Steve

 

[Killrose]

That is a great overclock, but that 1.95v is going to do that chip in a little early I would suspect. What are your temps?

 

[pillage2001]

Xp2100 AIUHB 0301 @ 2.2Ghz @ 1.7v

My CPU runs 60c at full load. Damn this case. The air flow in it sucks. Would have oc higher if not for the stupid case.

 

[M O M O]

Stepping:
AXDA1700DUT3C
JIUHB 0307SPMW

Speed:
10.5 x 220
1.825V

RAM:.
xms3500 512meg

Motherboard:
Abit nf7-s r1.2


Cooler:
alpha 8045
Arctic Silver 3

Just got a tbred B xp2100+ going to test it out once i get a replacement bio's chip

 

[bdunosk]

Stepping:
AXDA1700DLT3C
JIUHB0310UPMW
98800007281125

Speed:
2400MHz
12 x 200
1.85V

RAM:
Twinmos pc3200 2 x 256MB

Cooler:
DDen Maze3

I haven't messed too much with it, since I only got it last night. Pretty much running this high right off the bat, Prime95 is stable through a few tests. I don't like to run my computer on torture tests when I'm not around, especially when I first get the watercooling setup... so I will mess with it more and update as I overclock more. Outrageously fast, though.

 

[beatle]

Stepping:
(I forget, but it's 1.5v default)
JIUHB:0307VPMW

Stable (running) speed:
2200Mhz
11 x 200
1.70v

Motherboard
Abit NF7-S v2.0

RAM
1x512 Twinmos PC3200 @ 200mhz
2-2-2-6

Cooler
SK7 with 32cfm panaflo

Temps
64-70C Full Load
I wish there was some kind of consensus on temps...

Notes
This board undervolts quite a bit. I see 1.63-1.66v most of the time. I really can't be sure about the temps, so I've been reluctant to turn up the voltage much to go for 2300Mhz. Last night I gave it a try @ 2300, 1.75v (1.70v actual) and it booted fine. Primed for about 5-10 minutes, heating the CPU to 73C before I got a BSOD and a reboot, free of charge. I hear the NF7-S v2.0 reads hot, but I don't know HOW hot. I should have much lower temps than this.

 

[Shimmishim]

73 is pretty high....

i'm at 1.875volts and it's at 58C's on my abit nf7-s so.. 73 is quite high

 

[Shimmishim]

okay...

1.85volts actual... 1.93 in bios...

12.5 x 200 = 2500....

priming right now...

temps up to 56C's ... still 2C's lower than my slk800 @ 1.875volts...

so this is pretty good...

 

[Jen]

Originally posted by: Shimmishim
okay...

1.85volts actual... 1.93 in bios...

12.5 x 200 = 2500....

priming right now...

temps up to 56C's ... still 2C's lower than my slk800 @ 1.875volts...

so this is pretty good...

what week and stepping ?

 

[Link]

Originally posted by: beatle
Stepping:
(I forget, but it's 1.5v default)
JIUHB:0307VPMW

Stable (running) speed:
2200Mhz
11 x 200
1.70v

Motherboard
Abit NF7-S v2.0

RAM
1x512 Twinmos PC3200 @ 200mhz
2-2-2-6

Cooler
SK7 with 32cfm panaflo

Temps
64-70C Full Load
I wish there was some kind of consensus on temps...

Notes
This board undervolts quite a bit. I see 1.63-1.66v most of the time. I really can't be sure about the temps, so I've been reluctant to turn up the voltage much to go for 2300Mhz. Last night I gave it a try @ 2300, 1.75v (1.70v actual) and it booted fine. Primed for about 5-10 minutes, heating the CPU to 73C before I got a BSOD and a reboot, free of charge. I hear the NF7-S v2.0 reads hot, but I don't know HOW hot. I should have much lower temps than this.

Man, you temp is too high. Try to lower it to low 50's full load.

 

[skyking]

1700+ DUT3C 0307 SPMW ( I know, the dog chips )
crucial 2700
Abit kx7 333R
1.8 volts, 2.7 for the ram
184 X11 for 2024mhz
Temps at 32 mobo, 45 proc at full load.
$5 GC68 cooler from SVC

 

[qquizz]

AXDA1700DLT3C
9391067271066
JIUHB 0310XPMW
AMD Athlon XP 1700+ Retail CPU

 

[MangoX]

AXP 1800+ RETAIL @ 1900MHz 200x9.5 1.75v
AXDA1800DLT3C 4119427252299
AIUGA 0241MPM
OCZ PC3500 BASIC 2x256mb @ CAS2 2-252-2T 2.9V

 

[unchoops23]

OEM 1700+ at 185x11.5 (2.133Ghz - XP2600) @ 1.775V (47C under full stress)
512MB (2x256) Crucial pc2700 6-3-3-2.5 sync at 2.77V
Volcano 9 cooler
Epox 8rda+ Rev 1.1 (stock NB cooler, no SB cooler)
Radeon 8500 AIW (no oc'ing....yet)
3DMark2001SE: 10855
3DMark2003: 1853


Looks like right now my memory is the only thing keeping me from 2.4Ghz

 

[Shimmishim]

Originally posted by: unchoops23
OEM 1700+ at 185x11.5 (2.133Ghz - XP2600) @ 1.775V (47C under full stress)
512MB (2x256) Crucial pc2700 6-3-3-2.5 sync at 2.77V
Volcano 9 cooler
Epox 8rda+ Rev 1.1 (stock NB cooler, no SB cooler)
Radeon 8500 AIW (no oc'ing....yet)
3DMark2001SE: 10855
3DMark2003: 1853


Looks like right now my memory is the only thing keeping me from 2.4Ghz

how do you figure?

you have mults up to 12.5

you can still run 12.5 x 184 = 2.3 ghz but i dont' think you have too much room left considering you're at 1.775 volts already

 

[NesuD]

Stepping:
AXDA2100DUT3C
AIUHB0301MPMW

Speed:
2105 mhz
10.5 x 200.45
1.73V

RAM
GeIL PC3200 ULD dual channel kit
cas2-3-3-6

Cooler
Thermalright SK7 with Y.S. Tech Adjustable speed fan

 

[Shimmishim]

Originally posted by: NesuD
Stepping:
AXDA2100DUT3C
AIUHB0301MPMW

Speed:
2105 mhz
10.5 x 200.45
1.73V

RAM
GeIL PC3200 ULD dual channel kit
cas2-3-3-6

Cooler
Thermalright SK7 with Y.S. Tech Adjustable speed fan

keep going!!!

 

[scrubman]

Stepping:
AXDA1700DLT3C
JIUHB0310WPMW


Speed:
2200 mhz
11 x 200
1.65V

RAM
Twinmos/Winbond pc3200 2 x 256 megs 1.9V
2-3-3-6

Cooler
Thermalright SLK-800 with Panaflo H1A


I am so Excited! I have been working on this plan for 2 weeks now and finally have it all together and it thankfully meets my expectations! 15600 3DMark01 no trouble and still running Prime95 (been about 2 hours so far)...

Soooooooooo! is it better to stay at 2200 with a Cas2 than go to maybe 2300-2400 at Cas2.5?? Or what about lowering multiplier for higher frequency? Im guessing that i should stay right where I'm at... comments and suggestions welcome! Thanks to everyone here at Anand Tech for contributing and being so helpful with everything! this place is the BEST

 

[beatle]

Go for a higher fsb with cas 2.5.