Originally posted by: SavageThrash
Hye guys, first post so go easy on me
Well i have read up to page 20 in this thread and my goodness it has helped me an unbelivable amout (thnx phile)
I still have one question though, here are my specs
p5w dh deluxe
ocz platinum ddr2 pc2-6400 (same as you a belive phile)
e6400 stock speeds
x1300
620w enermax liberty
zalman 9500 cooler
The question i have is, i was running orthos and it ran for 1 hour and 5 minutes until
1:Test 7, 4500 Lucas-Lehmer iterations of M16297569 using 896K FFT length.
1:FATAL ERROR: Rounding was 0.4990234375, expected less than 0.4
1:Hardware failure detected, consult stress.txt file.
1:Torture Test ran 1 hours, 5 minutes 1 seconds - 1 errors, 0 warnings.
1:Execution halted.
thats the first core and the second finished that same test 7 just before that one died and I belive it was fine. heres core 2s message when the test was ended
2:Torture Test ran 1 hours, 5 minutes 1 seconds - 0 errors, 0 warnings.
2:Execution halted.
I decided to continue (i though it was continuing may have been a new one?)
Type: Blend - stress CPU and RAM Min: 8 Max: 4096 InPlace: No Mem: 1791 Time: 15
CPU: 2136MHz FSB: 266MHz [267MHz x 8.0 est.]
CPU: 2137MHz FSB: 266MHz [267MHz x 8.0 est.]
9/30/2006 2:15 PM
Launching 2 threads...
1:Using CPU #0
2:Using CPU #1
1:Beginning a continuous self-test to check your computer.
2:Beginning a continuous self-test to check your computer.
1ress Stop to end this test.
2ress Stop to end this test.
1:Test 1, 4500 Lucas-Lehmer iterations of M17432577 using 896K FFT length.
2:Test 1, 4000 Lucas-Lehmer iterations of M18274367 using 1024K FFT length.
2:Test 2, 4000 Lucas-Lehmer iterations of M18274369 using 1024K FFT length.
1:Test 2, 4500 Lucas-Lehmer iterations of M17432575 using 896K FFT length.
2:Test 3, 4000 Lucas-Lehmer iterations of M18074369 using 1024K FFT length.
1:Test 3, 4500 Lucas-Lehmer iterations of M17115073 using 896K FFT length.
2:Test 4, 4500 Lucas-Lehmer iterations of M17432577 using 1024K FFT length.
1:Test 4, 4500 Lucas-Lehmer iterations of M16815071 using 896K FFT length.
2:Test 5, 4500 Lucas-Lehmer iterations of M17432575 using 1024K FFT length.
1:Test 5, 4500 Lucas-Lehmer iterations of M16515073 using 896K FFT length.
2:Test 6, 4500 Lucas-Lehmer iterations of M17115073 using 1024K FFT length.
1:Test 6, 4500 Lucas-Lehmer iterations of M16515071 using 896K FFT length.
1:Test 7, 4500 Lucas-Lehmer iterations of M16297569 using 896K FFT length.
2:Test 7, 4500 Lucas-Lehmer iterations of M16815071 using 1024K FFT length.
1:Self-test 896K passed!
1:Test 1, 5300 Lucas-Lehmer iterations of M14942209 using 768K FFT length.
2:Self-test 1024K passed!
2:Test 1, 800000 Lucas-Lehmer iterations of M143361 using 8K FFT length.
1:FATAL ERROR: Rounding was 0.5, expected less than 0.4
1:Hardware failure detected, consult stress.txt file.
1:Torture Test ran 18 minutes 53 seconds - 1 errors, 0 warnings.
1:Execution halted.
2:Torture Test ran 18 minutes 53 seconds - 0 errors, 0 warnings.
2:Execution halted.
so i dont know what exactly is going on here, my comp doesnt crash or anything but i though that this would have lasted longer and with no errors.
any ideas?
EDIT: temps did not exceed 46 maybe 47c to my knowledge and i checked on it quite frequently
Sounds like the mem is crapping-out. Did you make sure to set the rated memory voltage and timings in the BIOS? If you're running the mem at 800MHz or less, set the voltage to 2.1v and the timings to 4-4-5-15 (sticker will say 4-5-4-15, but the BIOS has the order of the middle two values transposed).
If doing this does not help, consider running a memtest:
http://www.memtest.org
Burn ISO to CD and boot with it. Let it run through each of the 10 tests. In my experience, a bad dimm will cause errors on the first pass. If you get any errors, test with each stick separately. Errors on only one of the two dimms almost certainly means you have a bad dimm.
-phil